Lenovo thinksystem SN850 7X15 Скачать руководство пользователя страница 85

Страница: 85 / 88

Index

2.5-inch drive backplane

installing options

removing

activity LED

air baffle

removing

replacing

back up the compute node configuration

button, power

CMOS battery (CR2032)

collecting service data

Common installation issues

components

system board

compute node cover

installing

removing

compute node in the chassis

installing

Compute node setup

compute node setup checklist

Configuration - ThinkSystem SN850

configure the firmware

connectors, system board

cover

removing

CPU

option install

creating a personalized support web page

custom support web page

devices, static-sensitive

handling

DIMM

installing options

DIMM connectors

Drive status LED

fabric connector

location

fault LED

features

firmware updates

flash power module

installing

Getting help

guidelines

options installation

system reliability

handling static-sensitive devices

hardware options

installing

hardware service and support telephone numbers

HDD backplane connector

help

hot-swap hard disk or solid-state drive

installing options

identification LED

install the operating system

installation

guidelines

installation guidelines

installing

compute node

compute node cover

flash power module

installing options

2.5-inch drive backplane

DIMM

hot-swap hard disk or solid-state drive

interposer card

I/O expansion adapter

M.2 backplane

M.2 driver

RAID adapter

interposer card

installing options

introduction

I/O expansion adapter

installing options

I/O expansion connectors

jumpers, system board

KVM cable

LEDs

activity

fault

identification

power

Содержание thinksystem SN850 7X15

























































































Результаты поиска

Содержание thinksystem SN850 7X15

Отзывы:

Похожие инструкции для thinksystem SN850 7X15

Бренды по названию

Популярные бренды

Lenovo thinksystem SN850 7X15, Руководство по установке

Результаты поиска

Содержание thinksystem SN850 7X15

Отзывы:

Похожие инструкции для thinksystem SN850 7X15

Бренды по названию

Популярные бренды