Lenovo thinksystem SN850 7X15 Скачать руководство пользователя страница 38

Страница: 38 / 88

Figure 10. Compute node cover removal

Step 1. Press on the release button and the push point at the same time and slide the cover toward the rear

of the compute node.

Step 2. Lift the compute node cover away from the compute node.

Step 3. Lay the compute node cover flat or store it for future use.

Remove the air baffle

Use this information to remove the air baffle.

To avoid possible danger, read and follow the following safety information.

S012

CAUTION:
Hot surface nearby.

Before removing the air baffle:

1. Read “Installation Guidelines” on page 26 to ensure that you work safely.

2. Carefully lay the compute node on a flat, static-protective surface, orienting the compute node with the

bezel pointing toward you.

3. Remove the compute node cover (see “Remove the compute node cover” on page 29 for instructions).

To remove the air baffle, complete the following steps:

Watch the procedure

. A video of the installation process is available:

• Youtube: https://www.youtube.com/playlist?list=PLYV5R7hVcs-DtV8A4UWy7d3AoFKjCvas3
• Youku: http://list.youku.com/albumlist/show/id_50481024

ThinkSystem SN850 Compute Node Setup Guide

Содержание thinksystem SN850 7X15

























































































Результаты поиска

Содержание thinksystem SN850 7X15

Отзывы:

Похожие инструкции для thinksystem SN850 7X15

Бренды по названию

Популярные бренды

Lenovo thinksystem SN850 7X15, Руководство по установке

Результаты поиска

Содержание thinksystem SN850 7X15

Отзывы:

Похожие инструкции для thinksystem SN850 7X15

Бренды по названию

Популярные бренды