Lenovo thinksystem SN850 7X15 Скачать руководство пользователя страница 55

Страница: 55 / 88

Figure 29. Connecting the cable to RAID adapter

Step 8. Reinstall the RAID adapter (see “Install a RAID adapter” on page 47 for instructions).

Step 9. Route the cable in front of DIMM slots by inserting into clip mounted on side of storage cage.

Figure 30. Routing the cable

After you install the interposer card, complete the following steps:

1. For configure the RAID array, see

“RAID configuration” on page 65

for instructions.

Install a RAID adapter

Use this information to install a RAID adapter option.

Before you install a RAID adapter, complete the following steps:

1. Read “Installation Guidelines” on page 26 to ensure that you work safely.

2. Carefully lay the compute node on a flat, static-protective surface, orienting the compute node with the

bezel pointing toward you.

3. Remove the compute node cover (see “Remove the compute node cover” on page 29 for instructions).

To install the RAID adapter, complete the following steps:

Chapter 3

Compute node hardware setup

Содержание thinksystem SN850 7X15

























































































Результаты поиска

Содержание thinksystem SN850 7X15

Отзывы:

Похожие инструкции для thinksystem SN850 7X15

Бренды по названию

Популярные бренды

Lenovo thinksystem SN850 7X15, Руководство по установке

Результаты поиска

Содержание thinksystem SN850 7X15

Отзывы:

Похожие инструкции для thinksystem SN850 7X15

Бренды по названию

Популярные бренды