Lenovo thinksystem SN850 7X15 Скачать руководство пользователя страница 37

Страница: 37 / 88

• It is good practice to make sure that the compute node is working correctly before you install an optional

component.

• Follow the installation procedures in this section and use appropriate tools. Incorrectly installed

components can cause system failure from damaged pins, damaged connectors, loose cabling, or loose
components.

Remove the compute node cover

Use this information to remove the compute node cover.

To avoid possible danger, read and follow the following safety information.

•

S012

CAUTION:
Hot surface nearby.

•

S021

CAUTION:
Hazardous energy is present when the compute node is connected to the power source. Always
reinstall the compute node cover before installing the compute node.

1. Read “Installation Guidelines” on page 26 to ensure that you work safely.

2. Carefully lay the compute node on a flat, static-protective surface, orienting the compute node with the

bezel pointing toward you.

To remove the compute node cover, complete the following steps:

Watch the procedure

. A video of the installation process is available:

• Youtube: https://www.youtube.com/playlist?list=PLYV5R7hVcs-DtV8A4UWy7d3AoFKjCvas3
• Youku: http://list.youku.com/albumlist/show/id_50481024

Chapter 3

Compute node hardware setup

Содержание thinksystem SN850 7X15

























































































Результаты поиска

Содержание thinksystem SN850 7X15

Отзывы:

Похожие инструкции для thinksystem SN850 7X15

Бренды по названию

Популярные бренды

Lenovo thinksystem SN850 7X15, Руководство по установке

Результаты поиска

Содержание thinksystem SN850 7X15

Отзывы:

Похожие инструкции для thinksystem SN850 7X15

Бренды по названию

Популярные бренды