800.879.8585
www.legrand.us/wattstopper
No. 29188 – 01/20 rev. 1
© Copyright 2020 Legrand All Rights Reserved.
© Copyright 2020 Tous droits réservés Legrand.
© Copyright 2020 Legrand Todos los derechos reservados.
Wattstopper warranties its products to be free
of defects in materials and workmanship for a
period of five (5) years. There are no obligations
or liabilities on the part of Wattstopper for
consequential damages arising out of, or in
connection with, the use or performance of this
product or other indirect damages with respect
to loss of property, revenue or profit, or cost of
removal, installation or reinstallation.
Wattstopper garantit que ses produits sont
exempts de défauts de matériaux et de fabrication
pour une période de cinq (5) ans. Wattstopper
ne peut être tenu responsable de tout dommage
consécutif causé par ou lié à l’utilisation ou
à la performance de ce produit ou tout autre
dommage indirect lié à la perte de propriété, de
revenus, ou de profits, ou aux coûts d’enlèvement,
d’installation ou de réinstallation.
Wattstopper garantiza que sus productos
están libres de defectos en materiales y mano
de obra por un período de cinco (5) años. No
existen obligaciones ni responsabilidades por
parte de Wattstopper por daños consecuentes
que se deriven o estén relacionados con el
uso o el rendimiento de este producto u otros
daños indirectos con respecto a la pérdida
de propiedad, renta o ganancias, o al costo
de extracción, instalación o reinstalación.
WARRANTY INFORMATION
INFORMATIONS RELATIVES À LA GARANTIE
INFORMACIÓN DE LA GARANTÍA
3. Run the discovery process exactly like you would with a new installation.
4. Since you will have a new site file, you will have to reprogram all DLM parameters for the various devices.
If replacing or resetting an LMBR in a site with more than one LMBR, you do not have to create a new site. However you will need to:
1. Open the LMCS site file and delete the LMBR from the tree. If it was the Primary LMBR, one of the others will automatically
become the primary.
2. Reset ALL devices that are assigned to the network of the LMBR being replaced or reset (all other devices assigned to other
LMBRs do NOT need to be reset).
3. Run through the discovery process again to add the new/reset LMBR and then rediscover the devices that will connect to that
LMBR’s network. Once the devices have been reassigned to the network, there is no need to do any room assignment since they
already exist in the room in the project file. However, you will still need to re-pair devices by highlighting each room in the three
and clicking the
Wireless Device Pairing
button.
NOTE:
Keep in mind that if the old or reset LMBR was set to a static IP address, you will need to add a router back into the network in
order to communicate with the new or reset LMBR, since it will be set to DHCP. Be sure to set the LMBR-650 to static IP before
completing the process. It is not necessary to use the same static IP address as was used previously.
In order to enhance the security of our products, Legrand ships its products with all insecure ports closed and insecure protocols
disabled. You are free to configure your device as needed, but in doing so note that you may be decreasing the security of your device
and any information contained in the device. As you modify the device’s default settings, keep in mind how this may impact the security
of the device and your network. In addition, you should use caution in connecting your device to the Internet, especially if you have
altered the default security settings. If you have any questions or concerns about how your modifications of the device may affect its
security, please contact the Legrand customer service team at 1-800-879-8585 / https://www.legrand.us/support/wattstopper.aspx
