LeCroy ADP300 Скачать руководство пользователя страница 7

Страница: 7 / 39

ADP30X Operator’s Manual

ADP30X-OM-E Rev B

OVERVIEW...........................................................................................................3

Description .......................................................................................................................................3

Key Benefits .....................................................................................................................................3

Conventions Used in this Manual ....................................................................................................4

Standard Accessories.......................................................................................................................5

Description of Accessories...............................................................................................................5

SAFETY INFORMATION......................................................................................8

OPERATION.......................................................................................................10

Connecting the Probe to the Test Instrument.................................................................................10

Connecting the Probe to the Test Circuit .......................................................................................10

Operation with a LeCroy Oscilloscope...........................................................................................10

Smart Offset ................................................................................................................................... 11

Bandwidth Limit (ADP305 only) ..................................................................................................... 11

Auto Zero........................................................................................................................................ 11

REMOTE CONTROL COMMANDS....................................................................12

Introduction ....................................................................................................................................12

Command List ................................................................................................................................12

Probe Auto Zero .............................................................................................................................13

Probe Bandwidth Limit ...................................................................................................................14

Probe Coupling ..............................................................................................................................15

Probe Offset ...................................................................................................................................16

Probe Volts/div ...............................................................................................................................17

REFERENCE INFORMATION............................................................................18

Differential Mode and Common Mode ...........................................................................................18

Differential Mode Range and Common Mode Range....................................................................18

Common Mode Rejection Ratio .....................................................................................................18

CARE AND MAINTENANCE..............................................................................20

Cleaning .........................................................................................................................................20

Calibration Interval .........................................................................................................................20

Service Strategy .............................................................................................................................20

Troubleshooting..............................................................................................................................20

Returning a Defective Probe..........................................................................................................20

Replacement Parts.........................................................................................................................21

FUNCTIONAL TEST...........................................................................................23

Test Equipment Required...............................................................................................................23

Test procedure ...............................................................................................................................23

PERFORMANCE VERIFICATION ......................................................................24

Test Equipment Required...............................................................................................................24

Содержание ADP300








































Результаты поиска

Содержание ADP300

Отзывы:

LeCroy ADP300, Инструкция по эксплуатации, Страница: 7 / 39

Результаты поиска

Содержание ADP300

Отзывы: