LeCroy ADP300 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 39

LeCroy ADP300 Скачать руководство пользователя страница 12

ADP300/305 Probe

6

ADP30X-OM-E Rev B

Safety Alligator Clip

(1 Red, 1 Blue)

Insulated, 1000 V, CAT III. Designed to attach to large

components, such as busbars and large bolts, the overall
length is 90 mm (3.5 inches) and the jaw opens to 22 mm
(0.87 inch) max.

Plunger Jaw Clip

(1 Red, 1 Blue)

Insulated, 1000 V, CAT III. The clip is designed to securely
grasp thick wires, cables, ground leads, rails, and even screw
heads. The overall length is 134 mm (5.26 inches). The steel
jaw extends 12 mm (0.48 inch) and opens to 25 mm (1 inch).

Plunger Clamp Clip

(1 Red, 1 Blue)

Insulated, 1000 V, CAT III. Designed for attaching to hard-to-
reach test points, the entire body is fully insulated. The overall
length is 190 mm (7.5 inch). The clamp can grab leads, pins
and wires up to 5 mm (0.2 inch) in diameter.

Spade Terminal

Insulated, 1000 V, CAT III. Designed to connect to terminal
strips, posts, and screws, the overall length is 63 mm (2.48
inch).

«
...
10
11
12
13
14
...
»

Содержание ADP300








































Отзывы:

Нет отзывов