LC Packings SWITCHOS II Скачать руководство пользователя страница 26

Страница: 26 / 90

Installation and Getting Started

2-4

D850R3

User’s Manual Switchos

2.3.2

RS-232 Connectors

The two RS-232 serial interfaces enable digital data transfer between the loading
pump, the UltiMate Micropump, the UltiMate UV Detector (if present) and the

PC. These devices communicate with each other to form an integrated network.

To set up the RS-232 network connections:

•

Connect the RS-232

connector of the Switchos loading pump, the RS-232

connector of the UltiMate UV Detector and the COM port of the PC using

the Y-cable (item a, FIGURE 2-2).

•

Connect the RS-232

connector of the Switchos loading pump and the RS-

232

connector of the UltiMate Micropump using the Serial Communication

Cable (item b, FIGURE 2-2).

•

Connect the RS-232

connector of the Micropump and the RS-232

connector of the UV Detector with the same type of cable.

Switchos II

UltiMate

PC COM port X (SW II Valve Control)

PC COM port Y (Solvent Organizer)
PC COM port Z (ULT/SWII Network)

Item

P/N

Cable

a 160069

9 pin

female

9 pin

female

9 pin

male

b 160070

9 pin

male

9 pin

female

1:1

c 160071

9 pin

female

9 pin

female

Null-Modem

FIGURE 2-2 Setting up the RS-232 Network Connections

If your configuration does not include an UltiMate UV Detector, connect the
y-cable to the RS-232

connector of the UltiMate Micropump, the RS-232

connector of the Switchos loading pump and the COM port of the PC. Use a

Serial Communication Cable to connect the other RS-232 connectors of both
pumps.

CAUTION

Caution: The RS-232 sockets are to be used only with LC Packings software

products (e.g. CHROMELEON) or third vendor software that support the LC
Packings UltiMate System.

Содержание SWITCHOS II



























































































Результаты поиска

Содержание SWITCHOS II

Отзывы:

Похожие инструкции для SWITCHOS II

Бренды по названию

Популярные бренды

LC Packings SWITCHOS II, Руководство пользователя

Результаты поиска

Содержание SWITCHOS II

Отзывы:

Похожие инструкции для SWITCHOS II

Бренды по названию

Популярные бренды