background image

   

   

Lavit   Document:   TM170915-­‐A      

   

42   

Section   7:       Troubleshooting   
   

   

Potential   problems   and   solutions.   

   

Condition   

Possible   Solution   

   

Water   dripping   
continuously   
from   the   

dispense   area.   

   

   

After   the   dispensing   of   a   sparkling   beverage   or   sparkling   water   several   
drops   may   occur   as   the   sparkling   water   in   the   water   line   heats   up   and   
expands.   This   is   normal.   

   
Continuously   dripping   water   is   caused   by   foreign   material   lodged   in   the   

soda   water   solenoid.   Remove   the   soda   water   solenoid   per   the   instructions   
on   Page   xx   and   disassemble   the   solenoid   to   remove   any   trapped   material.   
   

   
Leaking   water   
from   the   rear   of   

the   unit.   

   

   
   

   
Possible   leak   issues:   
   

First   –   Check   the   still   water   drain   plug   and   then   check   the   inlet   water   line.   If   
those   connections   are   dry   and   not   the   source   of   the   water   leak,   remove   the   

top   cover   of   the   unit.   
   
Inspect   the   connections   on   the   top   of   the   water   tanks.   Remove   the   ozone   

generator   to   view   all   connections.   Ensure   all   fittings   are   tight   and   dry.   
Inspect   the   area   around   the   top   insulation   seam   towards   the   left   side   panel.   
If   there   is   wetness   in   that   area   the   leak   may   be   from   the   soda   tank   seal.   

   
Other   possible   sources   of   a   leak   are   the   soda   pump   inlet   fitting,   the   inlet   

solenoid,   or   the   cold   tank   drain   connection.   To   inspect   these   areas   remove   
the   back   panel   per   the   instructions   of   Page   XX.   Inspect   the   soda   pump   inlet   
fitting   for   leak   at   the   quick   connect   insert.   Inspect   the   connections   to   the   

inlet   solenoid.   If   those   connections   show   no   evidence   of   leaking   and   water   is   
captured   in   the   area   at   the   bottom   of   the   cold   water   tank,   the   water   drain   
connection   to   the   tank   may   be   the   cause   of   the   leak.   Remove   the   insulation   

from   around   the   water   tank   drain   pipe   and   inspect.      
   

Other   possible   sources   of   leaks   are   the   still   water   and   recirculation   pump   
connections   and   the   cooling   coil   connection   running   to   and   from   the   
compressor   and   condenser.   

   

   
No   Sparkling   

Water   Dispense,   
CO2   gas   only.   

   
If   the   soda   pump   is   not   filling   the   soda   tank   properly   then   CO2   gas   will   be   

released   at   the   dispense   nozzle   when   you   select   a   sparkling   beverage   or   
sparkling   water.      

Содержание LCB 100



























































Отзывы: