background image

   

   

Lavit   Document:   TM170915-­‐A      

   

20   

12.

 

The   dispenser   will   self-­‐check   on   every   power   up   and   if   OK   will   go   to   the   LCD   home   screen   
and   the   Lavit   Button   halo   will   be   red.   

   

13.

 

TO   FILL   THE   DISPENSER   WITH   WATER,   TURN   THE   LAVIT   PUMP   TO   ON,   PUSH   THE   
LAVIT   BUTTON   AND   THE   DISPENSER   WILL   START   TO   FILL.   

The   screen   will   display   a   

WATER   TANK   FILLING   SCREEN.   

   

   

14.

 

When   the   water   tanks   are   half   filled,   the   compressor   will   turn   on   and   start   to   chill.   The   soda   
pump   will   also   turn   on   when   the   water   tank   is   half   full.   The   HOME   screen   will   appear.   
   

15.

 

When   the   HOME   screen   appears   turn   the   CO

2

   gas   pressure   on.   

SET   THE   REGULATOR   TO   

3.5   BAR   OF   PRESSURE   BY   ROTATING   THE   KNOB   CLOCKWISE.   3.5   BAR   OF   PRESSURE   

(50   PSI)   IS   INDICATED   AT   THE   BEGINNING   OF   THE   RED   SCALE   ON   THE   REGULATOR

.   

The   soda   tank   will   fill   with   CO

2

   gas.   

   

   

   

   

16.

 

Purge   any   air   from   the   system   by   toggling   the   CO

2

   Purge   Valve   located   in   the   rear   of   the   

unit.   Purge   gas   about   3   times   for   2   seconds   each   time.   

   

17.

 

If   the   water   tanks   do   not   fill   within   5   minutes   the   water   inlet   valve   will   automatically   close.   

This   feature   is   a   safety   feature   that   prevents   the   continuous   running   of   water   in   the   case   of   
a   water   leak.   An   error   screen   indicating   a   possible   leak   will   be   displayed.   To   clear   the   
dispenser   of   this   condition   turn   the   power   off   and   then   back   on.   Reset   the   Lavit   Pump   if   

necessary   (Red   Light)   by   pushing   the   reset   button   on   the   pump.   The   reset   should   be   green.   
   

18.

 

Push   the   Lavit   Button   again   and   the   tanks   will   then   automatically   continue   filling   to   

capacity   and   shut   off   and   the   Lavit   button   halo   will   be   blue.   
   

19.

 

While   the   water   tanks   are   filling   and   the   compressor   is   chilling   the   water,   set   the   current   
date   and   time   by   pressing   the   gear   shaped   Service   Icon   on   the   lower   left   of   the   HOME   

Содержание LCB 100



























































Отзывы: