Lauterbach AutoFocus страница 39 Скачать руководство пользователя | Manualshive

Страница: 39 / 86

background image

AutoFocus User’s Guide

39

©1989-2018 Lauterbach GmbH

4. Check

TRACE32 differentiates between two views of data eyes:

•

Analog view of data eyes (check 5)

•

Digital view of data eyes: Check 4 is only about the digital view of data eyes.

Trace data is sampled at clock edges, on rising only or rising and falling. They must be stable around the
clock edge over a short time. This time window of stable data is reflected in so-called data eyes.

TRACE32 offers a powerful feature called

Analyzer.ShowFocus

to analyze the signal integrity of the trace

port.

Analyzer.ShowFocus

opens the digital

ShowFocus

window.

Analyzer.ShowFocus

is a kind of digital

view of the data eyes.

The horizontal axis reflects time line in nanoseconds. On the left, the current delay is shown for each trace
signal. The red line shows the sampling point. It can be different for each signal.
Data lines are delayed if values smaller than zero are set or not all sampling points are equal. In case of
values larger than zero, the clock line is delayed.

The horizontal axis shows all enabled signals listed. That means the number of signals depends on the
setup of the trace port. The window needs to be re-opened after the trace port setup has changed.

NOTE:

The data seen by the AutoFocus preprocessor depends highly from the clock
threshold setup. Depending on the signal integrity, the data eyes are more or
less wide open.

NOTE:

The data delay is used to eliminate data skew.
Clock delay is used to correct setup and hold times.
Both delays types can be used at the same time.

«
...
37
38
39
40
41
...
»

Содержание AutoFocus























































































Отзывы:

Нет отзывов

Похожие инструкции для AutoFocus

Бренд: Makita Страницы: 60

Бренд: JB-Lighting Страницы: 60

Бренд: Parr Instrument Страницы: 24

Бренд: JBL Страницы: 15

Бренд: HAMAR LASER Страницы: 49

Бренд: Cannon Страницы: 40

Бренд: NARGESA Страницы: 34

Бренд: Hanna Instruments Страницы: 2

Бренд: Hanna Instruments Страницы: 2

Бренд: Hanna Страницы: 12

Бренд: Hanil Страницы: 24

Бренд: Hanil Страницы: 32

Бренд: Hanil Страницы: 24

Бренд: TANDBERG Страницы: 23

Бренд: M-system Страницы: 5

Бренд: MA Страницы: 2

Бренд: UniPix Страницы: 24

Бренд: Gaspardo Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды