manualshive.com logo in svg

Lauterbach AutoFocus, Руководство пользователя, Страница: 58 / 86

Поделиться
Скачать
Lauterbach AutoFocus Скачать руководство пользователя страница 58

  AutoFocus User’s Guide

 

    58     

  

©1989-2018 Lauterbach GmbH

Pin Remapping

Functional Description - Pin Remapping

The actual pinout of the preprocessors is determined by several parameters, e.g. the CPU selection, the port 
type or port size. 

In order to display the current trace port configuration, just type 

Analyzer.REMAP.state

 into the TRACE32 

command line. The following window will open if the AutoFocus II is attached (a similar window will open for 
the AutoFocus MIPI):  

Each physical pin of the preprocessor’s connector is represented by the corresponding pin number in the 
diagram.

In case your target board does not comply with one of the preconfigured pinout configurations, you are 
usually required to buy or create an adaption board. But in case only the data and control pins (excluding the 
clock signal) need to be remapped, you can simply reconfigure the preprocessor’s pinout by selecting the 
adequate channel from the drop-down list.

NOTE:

The examples in this chapter refer to the pin remapping capability of the 
AutoFocus II (trace ID 0x71, 0x78) and AutoFocus II MIPI (trace ID 0x72) 
preprocessors. 

Any other preprocessors do not support pin remapping!

Example: AutoFocus II pinout for 32-bit ETMv3

Содержание AutoFocus























































































Отзывы:

Нет отзывов