Lauterbach AutoFocus страница 83 Скачать руководство пользователя | Manualshive

Страница: 83 / 86

background image

AutoFocus User’s Guide

83

©1989-2018 Lauterbach GmbH

Products

Product Information

OrderNo Code

Text

LA-7992

PP-ARM-ETM-AF-2

Preproc. for ARM-ETM/AUTOFOCUS II 600 Flex

Preprocessor for ARM7/ARM9/ARM10/ARM11/Cortex
Embedded Trace Macrocell (ETM),
Program Trace Macrocell (PTM),
Connector cable and software,
600 MHz clock speed, 4 x Trace-Depth,
Variable threshold level and termination voltage,
AUTOFOCUS self calibration technology,
Support all ETM modes, with 2 MICTOR connectors,
Supports 1.8 to 3.3V - else contact support
Requires PowerTrace/Ethernet Version 6 or higher
or PowerTrace II
Support max. 32 bit trace port size for ARM11
1 flex extension for Mictor 38pin connector
for target connection included

LA-7992A

PP-ARM-ETM-AF-2-ADD

Trace License for ARM-ETM AUTOFOCUS II

Supports off-chip trace port for ARM-ETM if
applied to an AUTOFOCUS II preprocessor
Extension applicable to the following preprocessors
(purchased separately):
for LA-3900 (Preproc. for PPC4XX AUTOFOCUS II)
for LA-3901 (Preproc. for MICROBLAZE AUTOFOCUS II)
for LA-3902 (Preproc. for SH3/SH4 (AUD) AUTOFOCUS II)
for LA-3903 (Preproc. for TMS AUTOFOCUS II)
for LA-3904 (Preproc. for TEAKLITE-III AUTOFOCUS II)
for LA-7995 (Preproc. for TMS320C55x AUTOFOCUS II)
for LA-7996 (Preproc. for Ceva-X AUTOFOCUS II)
for LA-7999 (Preproc. for StarCore AUTOFOCUS II)
please add the serial number of the preprocessor to
your order
AUTOFOCUS II Preprocessors with serial number
C0806xxxxxx and lower have to be send to Lauterbach
Germany for an hardware upgrade

LA-7993

PP-ARM-ETM-AF-MIPI

Preproc. for ARM-ETM/AUTOFOCUS 600 MIPI

Preprocessor for ARM7/ARM9/ARM10/ARM11/Cortex
Embedded Trace Macrocell (ETM),
Program Trace Macrocell (PTM),
Connector cable and software,
600 MHz clock speed, 4 x Trace-Depth,
Variable threshold level and termination voltage,
AUTOFOCUS self calibration technology,
Support all ETM modes, with SAMTEC60 MIPI connector,
Supports 1.8 to 3.3V - else contact support
supports up to 4 trace sources (mix of ETM and STM)
Minimum requirement: PowerTrace I Version 6 or higher
Recommended: PowerTrace II
Support max. 32 bit trace port size for ARM11
1 flex extension for SAMTEC60 MIPI connector
for target connection included (LA-1228)
includes Converter ARM-20 to MIPI-34 (LA-3770)

«
...
81
82
83
84
85
...
»

Содержание AutoFocus























































































Отзывы:

Нет отзывов

Похожие инструкции для AutoFocus

Бренд: Rain-Flo Irrigation Страницы: 20

Attest Auto-reader 390

Бренд: 3M Страницы: 2

Бренд: 3M Страницы: 2

Бренд: 3M Страницы: 2

PELTOR WS LiteCom Plus

Бренд: 3M Страницы: 7

Steri-Vac GS Series

Бренд: 3M Страницы: 52

Бренд: CAE Healthcare Страницы: 108

Бренд: Cannon Страницы: 36

Бренд: Haag-Streit Страницы: 18

Бренд: Haag-Streit Страницы: 20

Бренд: V-TEK Страницы: 2

Бренд: V-TEK Страницы: 112

Бренд: XanLite Страницы: 2

Бренд: X-Rite Страницы: 6

Бренд: Cannon Страницы: 70

Бренд: RAB Страницы: 4

Бренд: TEUCER Страницы: 4

KEW FORK 2300 R

Бренд: KYORITSU Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды