Manual: Purelight Series MK3
Manual: Purelight Series MK3
page 8 / 23
page 9 / 23
English
English
same mains!
12. Ensure sufficient ventilation and do not place the device on any warm or heat radiating
surface. Especially the ventilation openings must not be covered!
13. Ensure that device does not get overheated. Make sure that the device is not exposed
to spotlights (especially moving heads). Heat of spotlights could overheat laser in a little
while and leads to a degradation of performance.
4. Working on the device
1. This product has no user serviceable parts inside and should only be
maintained and serviced by a qualified engineer.
2. Be sure that the mains plug is not connected to the power
supply while installing the device.
3. Take off all reflecting things like rings, watches, etc. before
starting to work with or at the projector.
4. Only use non-reflecting tools to work on device.
5. Wear protective clothing (like goggles, gloves etc.)
according to laser power and wavelength of the laser.
5. Service notes
• Moisture and heat can reduce lifetime of the laser system dramatically and expires any
warranty claim.
• Quick on/off switching of this device will reduce durability of the laser diode dramatically.
• Avoid sharp knocks and shocks to this device an endsure sufficient protection during
transportation. Look after your Laserworld product.
• To increase durability of your laser, protect device against overheating:
-
Always ensure sufficient ventilation.
-
Do not face spotlights (especially moving heads) to the device.
-
Check temperature after approx. 30 minutes with each new installation. If necessary
install the projector at a place with different temperatures.
-
Switch off device when it is not needed. Diodes are switched on and can wear out even
if there is no visible laser output.
• Please ensure the fans and heatsinks are clear from dust and debris otherwise the risk
of overheating may occur. If the unit or air inlets appear to be blocked, please contact a
qualified service engineer to maintain and service the product.
• Always place the laser behind fog machines and hazers
• Clean the exit window with glass cleaner from time to time
• This Laserworld Purelight Series unit is IP54 waterproof. To maintain the waterproofness, it
is essential to follow these requirements:
-
all covers and flaps need to be closed and screws and parts to affix the covers / flaps
need to be in place and firmly attached.
-
all connectors used to control the laser or apply power to it must also be rated at least
IP54. The connectors must be connected in a way, that the IP rating must not be com-
promised.
-
it is strongly recommended to utilize the rain cover that is included in delivery to pro-
tect the laser system if it is used outdoors.
• If the housing has been opened, it requires professional re-sealing to maintain the IP ra-
ting. Please contact your Laserworld partner for assistance.
• This laser system is NOT suitable for underwater use. It can not be submerged.
• Removal of the warranty label as well as damages to the device caused by improper
handling, neglect of the safety instructions and service notes will void the warranty.
6. General Operation
1. Power
Connect the power cord to the device and to the mains. Make sure that your device is pro-
vided with the correct voltage. Wrong voltage could lead to irreparable damages. Please
find the correct voltage data in the synoptical table at the end of this manual. Make sure
that the device is not directed to people or inflammable objects during installation. To
start the device, connect the interlock bridge, insert the key and switch it on, and switch
the device on. The “Emission - Laser on“ LED at the front side of the device begins to
light up when the device is ready for use.
2. Key Switch
There is a key switch at the back of the laser system. Please plug the key to the switch and
turn it on. The laser device only runs when the key is inserted and switched on. Prevent
misuse! Unplug the key when the laser is unattended to prevent misuse of the sys-
tem.
3. Safety Presets
This device has an integrated Scan Safety (SFS). Is the Scan Safety active (on), single be-
ams are prevented. If the Scan Safety is switched off, it is possible to create full power
single beams - be careful!
Operating the laser system with disabled SFS may not be allowed in some countries.
Always ensure that maximum permissible exposure (MPE) is not exceeded in areas
accessible to the public or members of staff.
4. Modes / Functions
The different operation modes can be selected by using the rotating selector next to the
ShowNET-Display (or FB4) at the back of the device. Any change of the operation mode
for ShowNET devices requires a restart of the device (disconnect power and recon-
nect it again). Do not change any ShowNET-Display settings during operation, as random
and dangerous laser output can occur.
5. Turn device off
To turn off the device, use the power button („OFF“), turn the key to ‚OFF‘ and disconnect
the power cable from the mains.
