L’ARTISTICO SRL |
EN
23
Cod. 40115 | Rev. 13 | 09/09/2019
12. LOCATION OF THE PRODUCT
The fuel floor (parquet type) must be protected with special flame-
retardant plates (stainless steel, marble, tiles, etc.) to protect it from
radiant heat and the possible combustion of hot residues from
opening the door. Minimum distances from combustible materials
should be respected according to the requirements here indicated or
in the technical data sheet The chimney must be at least 50 cm away
from heat-sensitive building elements or flammable materials (wood
cladding, beams or ceilings, etc.)
For proper operation, the generator must be placed perfectly on a
horizontal (level) plane.
The appliance must be installed on a floor of adequate load capacity.
If the existing construction does not meet this requirement,
appropriate measures (ex: load distribution plate) should be taken.
The installation of the appliance must ensure easy
access to the cleaning and maintenance of the
appliance itself, the exhaust ducts and the chimney.
The appliance must be installed using the anti-vibration feet supplied
as standard. The anti-vibration mount, interposed between the
chimney and the supporting floor, significantly reduces the vibrations
harmful to the structures and annoying for people, leading to a
significant reduction in noise. We therefore advise against the
permanent anchoring of the fireplace to the floor by using cement or
hardening materials, to avoid vibrations and resonance phenomena
generated by the fans mounted on the appliance.
MINIMUM DISTANCES FROM FLAMMABLE MATERIALS:
A = 29 cm (Distance from the back)
B = 34 cm (Distance from side walls)
C = 100 cm (Distance from the glass of the appliance)
D = 60 cm (a protective plate of the floor made of flammable material)
E = 12 cm (Distance from inflammable floor)
These measures can be reduced using insulating
materials. Refer to the technical data sheet of the
insulating product that you will use to comply with local
and national regulations.
Keep all flammable material like wooden furniture,
curtains, carpets and flammable fluids at least 100 cm
from the appliance when operating.
MINIMUM
DISTANCES
FROM
NON-FLAMMABLE
MATERIALS:
In the case of non-flammable materials it is
necessary to maintain a lateral and posterior distance of
at least 10 cm. Only for products with rear spacers it is
permitted to install flush with the wall exclusively for the
rear part.
These distances are indispensable for cooling the body and for the
ordinary and extraordinary maintenance of your appliance.
13. COATING: AIR INPUT , INSPECTION AND
CANALIZATION
COATING
The coating must be self-supporting and flame-retardant and can not
be in contact with the appliance (
leave at least 5 mm air gap
between door profile and coating
). We also recommend isolating
the hood internally with Firerock panels (30 mm rock wool insulation
panels coupled to an aluminum foil, aluminum side to the fireplace),
respecting a minimum distance from the appliance by 5 cm.
AIR INTAKES IN THE COVERING
To avoid overheating of the appliance it is mandatory to carry out
inside the structure that covers the chimney, a recirculation of air with
one or more openings in the lower and upper part of the cladding.
The measures to be respected are the following:
- cold air inlet taken from the environment on the lower part of
minimum total area 450 cm²
- hot air outlet of natural convection on the upper part of
minimum total area 450 cm².
INSPECTION DOOR
Each pellet fireplace model requires a mandatory inspection door for
ordinary and extraordinary maintenance of the appliance of at
least
50x140 cm.
CONNECTING PIPES HOT AIR FANS
When the fans are present, they must be connected to air distribution
nozzles.
It is forbidden, subject to warranty termination, not
to connect the air hoses as shown in the following
diagram.
It is strictly forbidden to move the electrical
components and the smoke extractor at a later date, as
long as the guarantee is declined. It is an operation that
must be done exclusively at the factory or an authorized
service center.
According to the models respect the following indications.
AIR FIREPLACES WITH FRONT GLASS
(Models APOLLO 15, SERBIS M14, SERBIS EVO M14, ORION 13,
FRATAC M14, FRATAC EVO M14, SIRIUS 11, ROBIN M11)
