Lantronix WiPort NR Скачать руководство пользователя страница 62

Страница: 62 / 72

WiPort® NR Embedded Device Server User Guide

7: Monitor Mode

Monitor Mode is a command-line interface used for diagnostic purposes.
There are two ways to enter Monitor Mode: locally via the serial port or remotely via

the network.

Entering Monitor Mode via the Serial Port

To enter Monitor Mode locally:

1. Follow the same steps used for setting the serial configuration parameters (see

Serial Port Access

on page

2. Instead of typing three

keys, however:

3. Type

zzz

to enter Monitor Mode with network connections.

4. Type

yyy

to enter Monitor Mode without network connections.

prompt indicates that you have successfully entered Monitor Mode.

Entering Monitor Mode via the Network Port

To enter Monitor Mode using a Telnet connection:
1. Establish a Telnet session to the configuration port (9999). The following

message appears:

MAC address 00204AFFFF30

Software version V6.9.0.4 (130628)

Press Enter for Setup Mode

2. Type M (upper case).

prompt indicates that you have successfully entered Monitor Mode.

Monitor Mode Commands

The following commands are available in Monitor Mode.

Note:

All commands must be in capital letters.

Table 7-1. Monitor Mode Commands

Command

Command Name

Function

Version

Queries software header record (16 bytes) of unit.

Get Configuration

Gets configuration of unit as hex records (120

bytes).

Содержание WiPort NR









































































Результаты поиска

Содержание WiPort NR

Отзывы:

Lantronix WiPort NR, Руководство пользователя, Страница: 62 / 72

Результаты поиска

Содержание WiPort NR

Отзывы: