Lantronix WiPort NR страница 53 Скачать руководство пользователя

Страница: 53 / 72

5: Configuration via Serial Mode or Telnet Port

WiPort® NR Embedded Device Server User Guide

Disable TFTP Firmware Upgrade

This setting defaults to the

(No) option. The

(Yes) option disables TFTP for

network firmware upgrades.

Disable TFTP Firmware Update (N) : _

Disable Port 77FE (Hex)

Custom programs use Port 77FE to configure the unit remotely. If required,

disable this capability for security purposes.

Disable Port 77FEh (N) ? _

The default setting is the

(No) option, which enables remote configuration.

Disable Web Server

The

(Yes) option disables the web server. This setting defaults to the N (option).

Disable Web Server (N) ? _

Disable Web Setup

The

(Yes) option disables configuration via the Web Manager. This setting defaults

to the N (option).

Disable Web Setup (N) ? _

Disable ECHO Ports

This setting controls whether port 7 echoes characters it receives.

Disable ECHO ports (Y) ? _

Enable Encryption

Rijndael is the block cipher algorithm chosen by the National Institute of Science and

Technology (NIST) as the Advanced Encryption Standard (AES) to be used by the

US government. The WiPort NR device supports 128-, 192-, and 256-bit encryption

key lengths.

Note:

Configuring encryption should be done through a local connection to the serial

port of the WiPort NR device server, or via a secured network connection. Initial

configuration information including the encryption key is sent in clear text over the

network.

To configure AES encryption on WiPort NR module:

Enable Encryption (N) ?

Enable Enhanced Password (N) ?

Disable Port 77F0h (N) ?

Enable Encryption

This option enables AES encryption for tunneling only.

Key Length in bits

Valid options are 128, 192 and 256 bits.

Содержание WiPort NR









































































Результаты поиска

Содержание WiPort NR

Отзывы:

Похожие инструкции для WiPort NR

Бренды по названию

Популярные бренды

Lantronix WiPort NR, Руководство пользователя

Результаты поиска

Содержание WiPort NR

Отзывы:

Похожие инструкции для WiPort NR

Бренды по названию

Популярные бренды