Lang GCCO-T Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 73

Lang GCCO-T Скачать руководство пользователя страница 9

9

INSTALLATION CONT’D

Gas Conversions

1.  Disconnect oven from power and gas.
2.  Remove bottom trim piece from oven (2 hex head bolts and 1 Phillips screw).
3.  Remove side panel from oven.
4.  Disconnect black manifold pipe from 3/8” aluminum pipe at the furrel nut.
5.  Remove two Phillips screws holding black manifold pipe to oven.
6.  Remove black manifold pipe from oven.
7.  Remove both burner orifices from manifold and replace with new orifices, making

sure to apply pipe thread compound.

8.  Remove two Phillips screws holding pilot assembly to oven.
9.  Remove pilot assembly from oven.
10.  Remove ¼” aluminum pipe from pilot assembly.
11.  Remove pilot orifice and replace with new pilot orifice.
12.  Re-attach ¼” aluminum pipe to pilot assembly.
13.  Re-attach pilot assembly to oven.
14.  Re-install black manifold assembly to oven, making sure that the orifice goes into

the burner tubes.

15.  Re-attach 3/8” aluminum pipe to black manifold assembly.
16.  Remove the seal screw from the combination gas valve.
17.  Remove the adjustment screw and spring from the combination valve.
18.  Insert new spring into the valve and adjustment screw.
19.  Re-connect oven to power and gas and check for leaks using a soap solution.
20.  Adjust gas pressure to correct water column (5”NG, 10”LP).
21.  Install new seal screw provided in kit and affix “Caution” sticker to the visible side

of the combination valve.

22. Re-install bottom trim piece and side panel.

NG to LP

LP to NG

Part No.

Description

Qty.

Part No.

Description

Qty.

80401-05 Pilot Orifice, Drilled .010

1

80401-10 Pilot Orifice, Drilled .018

1

80400-14 Main Burner Orifice, Drilled #53 2

80400-13 Main Burner Orifice, Drilled #43

2

80505-11

Combination Gas Valve Spring,
Includes:

1. Spring
2. Seal

Screw

3. Caution

Sticker

1

80505-16

Combination Gas Valve Spring,
Includes:

1. Spring
2. Seal

Screw

3. Caution

Sticker

1

«
...
7
8
9
10
11
...
»

Содержание GCCO-T










































































Отзывы:

Нет отзывов