manualshive.com logo in svg

Lang GCCO-T, Руководство по обслуживанию, Страница: 53 / 73

Поделиться
Скачать
Lang GCCO-T Скачать руководство пользователя страница 53

 

53

TROUBLESHOOTING GCCO-PP / -PT CONT’D 

NO HEAT, MANUAL MODE 

PROBABLE CAUSE 

CORRECTIVE ACTION 

Defective back-up toggle 
switch 

 

Confirm that toggle switch is in the “ON” position. 

 

Check toggle switch for normal operation. 

Defective back-up relay 

 

Check for 120VAC at relay coil. 

If no voltage is present: 

 

Confirm that points are making. 

If voltage is present: 

 

Replace relay.

 

Defective component 
transformer 

 

Confirm that 120VAC is feeding primary coil. 

 

Confirm that 24VAC is at secondary coil. 

Failed Ignition 

 

See Failed Ignition portion of this manual. 

 

Check for 24VAC at MV on the spark modual to ground. 

If no voltage is present: 

 

Confirm that pilot is lit. 

 

Replace as necessary. 

If voltage is present: 

 

Check thermostat for normal operation. 

Defective Thermostat 

 

Confirm that thermostat has 24VAC. 

If no voltage is present 

 

Check component transformer and wiring for normal operation.

 

If voltage is present 

 

Check thermostat for normal operation.  Replace as necessary. 

Defective centrifugal switch in 
motor 

 

Disconnect centrifugal switch and check of continuity while the 
motor is running. 

If no continuity is present: 

 

Replace motor. 

If continutiy is present: 

 

Check thermostat for normal operation.

 

 

Check wires

 

Defective main valve 

 

Check for 24VAC across valve. 

If no voltage is present: 

 

Confirm that wires have continuity. 

If voltage is present: 

 

Replace valve. 

Содержание GCCO-T










































































Отзывы:

Нет отзывов