manualshive.com logo in svg

Lang GCCO-T, Руководство по обслуживанию, Страница: 52 / 73

Поделиться
Скачать
Lang GCCO-T Скачать руководство пользователя страница 52

 

52

TROUBLESHOOTING GCCO-PP / -PT CONT’D 

NO MOTOR, MANUAL MODE 

PROBABLE CAUSE 

CORRECTIVE ACTION 

Defective back-up toggle 
switch 

 

Confirm that toggle switch is in the “ON” position. 

 

Check toggle switch for normal operation. 

Defective back-up relay 

 

Check for 24VAC at relay coil. 

If no voltage is present: 

 

Confirm that points are making. 

If voltage is present: 

 

Replace relay.

 

Defective component 
transformer 

 

Confirm that 120VAC is feeding primary coil. 

 

Confirm that 24VAC is at secondary coil. 

Defective motor relay 

 

Check for 24VAC at relay coil. 

If no voltage is present: 

 

Confirm that points are making. 

If voltage is present: 

 

Replace relay.

 

Defective motor 

 

Check for 120VAC across P1 and T7/T4. 

If no voltage is present: 

 

Confirm that wires have continuity. 

If voltage is present: 

 

Replace motor. 

NO MOTOR, COMPUTER MODE 

IMPORTANT NOTICE: 

Before trying to trouble shoot “No Motor in Computer Mode” confirm that motor is 

operational in “Manual Mode”.  

 

PROBABLE CAUSE 

CORRECTIVE ACTION 

Defective output on CPU 
board 

 

Check for 24VAC at JP12 for high or JP13 for low (while oven is 
calling for heat). 

If no voltage is present: 

 

Board is operating correctly. 

If voltage is present: 

 

Replace CPU. 

Содержание GCCO-T










































































Отзывы:

Нет отзывов