manualshive.com logo in svg

Lang GCCO-T, Руководство по обслуживанию, Страница: 30 / 73

Поделиться
Скачать
Lang GCCO-T Скачать руководство пользователя страница 30

 

30

TYPICAL OPERATION  

GCCO-AP TYPICAL OPERATION SEQUENCE 

ACTION

 

RESULT

 

Turn power switch to ON. 

Control panel heat call light comes on. 

Adjust proper temperature, between 140 & 450 
degrees and allow to preheat up to 20 minutes. 

Oven begins heating. 

Open oven doors and insert product, set timer up to 
60 minutes. 

Timer begins counting down. 

Timer beeps continuously when done.

 

Product should now be done. 

GCCO-T TYPICAL OPERATION SEQUENCE 

ACTION

 

RESULT

 

Turn power switch to ON. 

 

Adjust proper temperature, between 140 & 450 
degrees and allow to preheat up to 20 minutes. 

Oven begins heating. 

Open oven doors and insert product, set timer up to 
60 minutes. 

Timer begins counting down. 

Timer beeps continuously when done.

 

Product should now be done. 

GCCO-SII TYPICAL OPERATION SEQUENCE 

ACTION

 

RESULT

 

Turn power switch to ON. 

Digital display reads “

000

”

”.  

Press Temp button and use arrows to adjust to 
proper Temp between 150 & 450. 

Oven begins heating and displays “

pre

”. 

Beeper will sound for 3 seconds when preheated.

  

Open doors and insert product. 

Display will read preheated temperature. 

Press Time Button and use arrows to adjust to 
desired time.  Press Start / Stop Button.

 

Digital display will start countdown. 

Beeper sounds continuously 

Press Start / Stop 

Button. 

 

 

Содержание GCCO-T










































































Отзывы:

Нет отзывов