manualshive.com logo in svg

Lang GCCO-T, Руководство по обслуживанию, Страница: 45 / 73

Поделиться
Скачать
Lang GCCO-T Скачать руководство пользователя страница 45

 

45

TROUBLESHOOTING GCCO-C CONT’D 

 

PROBABLE CAUSE 

CORRECTIVE ACTION 

Defective control transformer 
(12 VAC). 

 

Check transformer for normal operation.

 

 

Check primary coil for 120 VAC and 154.1 

Ω

.  Check secondary coil 

for no less than 10.5 VAC and 1 

Ω

. 

If voltage is measured on primary: 

 

Check for voltage on secondary. 

 

Replace transformer. 

If voltage is not measured on primary: 

 

Check wires for any shorts. 

Defective rectifier 

 

Check for no less than 10.5 VAC on 

TP1

 and 5 VDC on 

TP2

.

 

 

If correct voltage is present at 

TP1

 and present, but low at 

TP2

 

unplug both ribbon connections from CPU and re-measure at 

TP2

. 

 

If voltage remains low at 

TP2

 replace CPU (40102-311). 

 

If voltage at 

TP2

 increased to 5 VDC when ribbon was unplugged, 

plug ribbon back in to CPU and disconnect from Interface board. 

 

Re-measure at 

TP2

. 

 

If voltage dropped to below 5 VDC replace ribbon cable (31110-01). 

 

If voltage remains at 5 VDC, plug ribbon back into Interface board 
and measure for 5 VDC at 

TP3.

 

 

If voltage is present at 

TP3

 and display is still not on, press and hold 

the 

R/C

 button on board if LED’s come on replace Interface board. 

 

If LED segment does not illuminate or the LED is blank, replace 
LED. 

 
Note: Display should now be operating.

 

Содержание GCCO-T










































































Отзывы:

Нет отзывов