manualshive.com logo in svg

Lang GCCO-T, Руководство по обслуживанию, Страница: 55 / 73

Поделиться
Скачать
Lang GCCO-T Скачать руководство пользователя страница 55

 

55

TECHNICAL DATA 

 
 

TRANSFORMER RESISTANCE 

TRANSFORMER Input  Primary 

Secondary 

Output 

 

120/24 Volt 

120 Volt 

18.9 

Ω

 

1

Ω

 

24 Volt 

 

120/12 Volt 

120 Volt 

154.1 

Ω

 1 

Ω

 

12 Volt 

 

24/24 Volt 

24 Volt 

2.7 

Ω

 3.4 

Ω

 

24 Volt 

CONTACTOR RESISTANCE 

CONTACTOR Coil 

 

3 Pole 24 Volt coil 

6 

Ω

 

 

2 Pole 24 Volt coil (P & B) (PP & PT motor) 

35 

Ω

 

RELAY RESISTANCE

 

RELAY Coil 

 

24 VAC 

82 

Ω

 

OVER-TEMP THERMOSTAT 

OVER-TEMP 

 

Wires  

Normally closed 

DOOR SWITCH 

 

Check switch between “COM” (common) and “NO” (normally open) contacts, insure switch closes approximately 3 to 4 
inches before door closes. 

BLOWER FAN 

 

Blower fan will rotate clockwise and should have a 5/8“ gap between it and the back wall of the can. 

AUTO/BYPASS SWITCH 

The Auto / Bypass and Energy switch are located below the controls behind a pull down access panel 

 

Auto/Bypass switch 

Normally in 

“OFF”

.  The 

“ON”

 position will interrupt 

power to the computer and allow use of the back-up 
thermostat. 

 

Energy switch 

Normally in 

“HIGH”

 for 11 kW heats.  

“LOW”

 WILL 

PROVIDE 8.25 kW heat.  Not provided on Steam 
convection ovens. 

 
 

Содержание GCCO-T










































































Отзывы:

Нет отзывов