manualshive.com logo in svg

Lang GCCO-T, Руководство по обслуживанию, Страница: 51 / 73

Поделиться
Скачать
Lang GCCO-T Скачать руководство пользователя страница 51

 

51

TROUBLESHOOTING GCCO-PP / -PT CONT’D 

NO DISPLAY 

PROBABLE CAUSE 

CORRECTIVE ACTION 

Defective Power Switch (-PP 
only) 

 

Confirm that toggle switch is getting correct voltage. 

 

Check power switch for normal operation. 

Defective Power Switch 
output on circuit board 
(JP37) 

 

Confirm that JP37 has 5VDC in the off position and nominal voltage 
in the on position. 

 

If JP37 has a constant 5VDC check toggle switch for normal 
operation. 

Defective Control 
Transformer 

 

Confirm that 208/240VAC is feeding primary coil. 

 

Confirm that 24VAC and 12VAC is at JP40 (24VAC across solid 
yellow wires and 12VAC from one solid yellow wire to yellow with 
red stripe). 

Defective Display 

 

Check ribbon cable connections. 

 

Confirm that voltage is present at JP40. 

If no voltage is present: 

 

Replace control transformer.

 

If voltage is present: 

 

Confirm that CPU has 5VDC at TP1 (this means that the CPU is 
getting correct voltage). 

 

Confirm that CPU has 12VDC at TP2 (this means that the CPU is 
sending out the correct voltage). 

If no voltage is present: 

 

Replace CPU. 

If voltage is present: 

 

Replace display. 

Содержание GCCO-T










































































Отзывы:

Нет отзывов