manualshive.com logo in svg

Lang GCCO-T, Руководство по обслуживанию, Страница: 33 / 73

Поделиться
Скачать
Lang GCCO-T Скачать руководство пользователя страница 33

 

33

SEQUENCE OF OPERATION GCCO-T 

 

Power to oven 

light

 

switch

 . 

120/24-volt 

transformer

 energized. 

24 volts to 

6

 (Johnson Control), 

TH 

(Channel Products), and 

ground

 of 

spark module.

 

Spark module begins sparking at pilot burner. 

24 volts to pilot valve coil of 

combination gas valve.

 

Pilot valve opens. 
Gas flows to 

pilot

 

burner.

 

Pilot burner lights. 

Pilot light confirmed by spark module. 

12 to 13 micro amps on pin 

4 

(Johnson Control), and 

Sens 

(Channel products). 

24 volts from pin 

3 

(Johnson Control) and 

MV 

(Channel products) to isolation transformer. 

24-volt isolation 

transformer

 energizes. 

24 volts to pins 9 and 7 of 

circuit

 

board

. 

24 volts to 

motor

 

relay

 through door switch and pulse-fan switch. 

Motor relay 

closes energizing motor and closing centrifugal switch. 

Temperature set on 12-position switch. 

24 volts from circuit board to 

MV 

on combination valve through pulse-switch, centrifugal switch, 

and over temperature thermostat. 
Main burner ignites. 

 
 

SEQUENCE OF OPERATION GCCO-AP 

 

Power switch turned to “ON” position. 

Power to oven 

light

 

switch

 . 

120/24-volt 

transformer

 energized. 

24 volts to 

6

 (Johnson Control), 

TH 

(Channel Products), and 

ground

 of 

spark module.

 

Spark module begins sparking at pilot burner. 

24 volts to pilot valve coil of 

combination gas valve.

 

Pilot valve opens. 
Gas flows to 

pilot

 

burner.

 

Pilot burner lights. 

Pilot light confirmed by spark module. 

12 to 13 micro amps on pin 

4 

(Johnson Control), and 

Sens 

(Channel products). 

24 volts from pin 

3 

(Johnson Control) and 

MV 

(Channel products) to isolation transformer. 

24-volt isolation 

transformer

 energizes. 

24 volts to pins 9 and 7 of 

circuit

 

board

. 

24 volts to 

motor

 

relay

 through door switch and pulse-fan switch. 

Motor relay 

closes energizing motor and closing centrifugal switch. 

Temperature set on 12-position switch. 

24 volts from circuit board to 

MV 

on combination valve through pulse-switch, centrifugal switch, 

and over temperature thermostat. 
Main burner ignites. 

 

Содержание GCCO-T










































































Отзывы:

Нет отзывов