manualshive.com logo in svg

Land Pride RCF2060, Руководство оператора

Поделиться
Скачать
Land Pride RCF2060 Скачать руководство пользователя страница 2

Table of Contents

RCF2060 and RCF2072 Rotary Cutters   326-459M

10/18/16

© 

Copyright 2016 All rights Reserved

Land Pride provides this publication “as is” without warranty of any kind, either expressed or implied. While every precaution has been taken in the
preparation of this manual, Land Pride assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use
of the information contained herein. Land Pride reserves the right to revise and improve its products as it sees fit. This publication describes the state of this
product at the time of its publication, and may not reflect the product in the future. 

Land Pride is a registered trademark.

All other brands and product names are trademarks or registered trademarks of their respective holders.

Printed in the United States of America.

Important Safety Information  . . . . . . . . . . . . .  1

Safety at All Times   . . . . . . . . . . . . . . . . . . . . . . . . . 1
Look For The Safety Alert Symbol . . . . . . . . . . . . . . 1
Safety Labels   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Introduction  . . . . . . . . . . . . . . . . . . . . . . . . . . .  7

Application   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Using This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Terminology:   . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Definitions:  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Owner Assistance  . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Serial Number   . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Further Assistance  . . . . . . . . . . . . . . . . . . . . . . . . 7

Section 1: Assembly & Set-up   . . . . . . . . . . . .  8

Tractor Requirements  . . . . . . . . . . . . . . . . . . . . . . . 8
Torque Requirements  . . . . . . . . . . . . . . . . . . . . . . . 8
Uncrating Instructions  . . . . . . . . . . . . . . . . . . . . . . . 8
Gearbox Vented Dipstick . . . . . . . . . . . . . . . . . . . . . 8
3-Point Hitch & Tailwheel Assembly   . . . . . . . . . . . . 8
Driveline Installation   . . . . . . . . . . . . . . . . . . . . . . . 10
Tractor Hook-Up  . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Hook-Up Driveline to Tractor PTO  . . . . . . . . . . . 11
Check Clearances   . . . . . . . . . . . . . . . . . . . . . . . 12
Check Driveline Collapsible Length  . . . . . . . . . . 12
Shorten Driveline  . . . . . . . . . . . . . . . . . . . . . . . . 12
Check Driveline Maximum Length   . . . . . . . . . . . 12
Check Driveline Interference   . . . . . . . . . . . . . . . 12

Section 2: Accessory & Options Set-up   . . .  14

Replaceable Skid Shoes (Accessory)  . . . . . . . . . . 14
Optional Front Guards  . . . . . . . . . . . . . . . . . . . . . . 14

Front Single Chain Guard Assembly   . . . . . . . . . 14
Front Rubber Guard Assembly . . . . . . . . . . . . . . 14

Optional Rear Guards  . . . . . . . . . . . . . . . . . . . . . . 15

Removal of Rear Metal Band Deflector   . . . . . . . 15
Rear Single Chain Guard  . . . . . . . . . . . . . . . . . . 15
Rear Rubber Guard installation   . . . . . . . . . . . . . 15

Section 3: Adjustments  . . . . . . . . . . . . . . . . .  16

Deck Leveling & Cutting Height  . . . . . . . . . . . . . . . 16
Deck Leveling From Left to Right   . . . . . . . . . . . . . 16
Deck Cutting Height   . . . . . . . . . . . . . . . . . . . . . . . 16
Tailwheel Height Adjustment  . . . . . . . . . . . . . . . . . 17
Tractor Center 3-Point Adjustment   . . . . . . . . . . . . 17

Section 4: Operating Instructions  . . . . . . . . . 18

Operating Checklist  . . . . . . . . . . . . . . . . . . . . . . . . 18
Safety Information  . . . . . . . . . . . . . . . . . . . . . . . . . 18
Inspection of Tractor & Cutter   . . . . . . . . . . . . . . . . 19
Transporting   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Blade Engagement & Disengagement  . . . . . . . . . . 20

Blade Engagement  . . . . . . . . . . . . . . . . . . . . . . . 20
Blade Disengagement   . . . . . . . . . . . . . . . . . . . . 20

Unhook Rotary Cutter   . . . . . . . . . . . . . . . . . . . . . . 20
Field Operation   . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
General Operating Instructions   . . . . . . . . . . . . . . . 21

Section 5: Maintenance & Lubrication  . . . . . 22

Maintenance   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Cutter Blade Maintenance  . . . . . . . . . . . . . . . . . . . 22
Driveline Protection  . . . . . . . . . . . . . . . . . . . . . . . . 23

Shearbolt Protected Drivelines  . . . . . . . . . . . . . . 23

Slip-Clutch Protected Drivelines   . . . . . . . . . . . . . . 23
Clutch Run-In   . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Clutch Assembly and Disassembly   . . . . . . . . . . . . 24

Disassembly  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Accessory Skid Shoe Maintenance  . . . . . . . . . . . . 24
Long Term Storage  . . . . . . . . . . . . . . . . . . . . . . . . 25
Ordering Replacement Parts  . . . . . . . . . . . . . . . . . 25
Lubrication Points   . . . . . . . . . . . . . . . . . . . . . . . . . 26

Gauge Wheel Spindle Tube  . . . . . . . . . . . . . . . . 26
Gauge Wheel Hub   . . . . . . . . . . . . . . . . . . . . . . . 26
Gearbox  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Driveline U-Joints  . . . . . . . . . . . . . . . . . . . . . . . . 27
Driveline Shield Bearings  . . . . . . . . . . . . . . . . . . 27
Driveline Profiles   . . . . . . . . . . . . . . . . . . . . . . . . 27

Section 6: Specifications & Capacities . . . . . 28
Section 7: Features & Benefits  . . . . . . . . . . . 30
Section 8: Troubleshooting  . . . . . . . . . . . . . . 31
Section 9: Torque values Chart . . . . . . . . . . . 32
Section 10: Warranty  . . . . . . . . . . . . . . . . . . . 33

Table of Contents

Содержание RCF2060





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды