manualshive.com logo in svg

Land Pride RCF2060, Руководство оператора

Поделиться
Скачать
Land Pride RCF2060 Скачать руководство пользователя страница 18

16

Section 3: Adjustments

RCF2060 and RCF2072 Rotary Cutters   326-459M

10/18/16

Table of Contents

Deck Leveling & Cutting Height

There are 4 primary adjustments that should be made 
prior to actual field operation:

•

Deck Leveling From Left to Right

•

Deck Cutting Height 

•

Tractor Center 3-Point Adjustment 

•

Tailwheel Height Adjustment

Proper adjustment of each of these items will provide for 
higher efficiency, improved cutting performance, and 
longer blade life. The following tools will be needed:

•

Pliable tape measure

•

Spirit or carpenters level

•

Set of wrenches and/or socket wrench set

•

Protective gloves

!

WARNING

Always disengage PTO, put tractor in park or set park brake, 
shut tractor engine off, remove ignition key, and wait for 
blades to come to a complete stop before dismounting tractor. 

Deck Leveling From Left to Right

Refer to Figure 3-1:

1.

Locate tractor with Rotary Cutter on a flat, level 
surface.

2.

Use tractor’s hydraulic 3-point control lever to lower 
cutter until tailwheel makes contact with ground 
surface.

3.

Place a level on the cutter deck as shown. Manually 
adjust one or both lower 3-point lift arms until deck is 
level from left to right. On some tractors, only one arm 
can be adjusted vertically. 

Section 3: 

Adjustments

Cutting Height

Figure 3-2

Set Front Blade Tip 
At Cutting Height

Blade Tip

Blade Tip

Set Rear Blade Tip Slightly 
Higher Than Cutting  Height

30987

Deck Leveling

Figure 3-1

Deck Cutting Height

Refer to Figure 3-2:

!

CAUTION

Avoid direct contact with cutter blades by wearing a pair of 
gloves. Cutter blades have sharp edges and burrs that can 
cause injuries. 

1.

With gloves on, carefully rotate each blade tip to the 
position shown in Figure 3-2.

2.

Measure distance from cutting tip of front blade to 
ground surface. This distance is the cutting height.

30988

spirt Level

IMPORTANT: 

The front blade tip should be lower 

than rear blade tip by approximately 1". The cutter is 
subject to continuous material flow under the deck if 
the rear blade is at the same height or lower than the 
front blade causing horsepower loss, grass clumps, 
blade wear, and frequent blade sharpening.

Содержание RCF2060





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды