manualshive.com logo in svg

Land Pride RCF2060, Руководство оператора

Поделиться
Скачать
Land Pride RCF2060 Скачать руководство пользователя страница 28

26

Section 5: Maintenance & Lubrication

RCF2060 and RCF2072 Rotary Cutters   326-459M

10/18/16

Table of Contents

Lubrication Points

Gauge Wheel Spindle Tube

Type of Lubrication: Grease

Quantity = 6 pumps

Gauge Wheel Hub

Type of Lubrication: Multi-purpose Grease

Quantity = 2 pumps

Gearbox

Method 1:

 Unscrew top vented dipstick (#1). Wipe oil 

from dipstick and screw dipstick in without tightening. 
Unscrew dipstick and check oil on dipstick. If below 
bottom level mark, add recommended gear lube through 
dipstick hole until oil reaches top mark on dipstick. 
Reinstall vented dipstick and tighten.

Method 2:

 Remove side oil plug (#2). If oil is below 

bottom of plug hole, add recommended gear lube 
through top dipstick hole until oil flows out of side plug 
hole. Reinstall and tighten side oil plug (#2) and vented 
dipstick (#1).

Type of Lubrication: 80-90W EP Gear Lube 

Quantity = Fill until oil reaches top mark on dipstick or 
begins to flow out side plug hole in gearbox.

NOTE:  

Do not overfill! Cutter should be level when 

checking oil. Oil expands when hot, therefore, always 
check oil level when cold.

30991

Solid Rubber Tire

30992

Laminated Tire

30991

30215

Do Not Overfill

IMPORTANT: 

This implement is shipped with a vented 

dipstick packaged in the Operator’s Manual bag and 
should have been installed in the gearbox by your 
dealer. Please consult your dealer if vented dipstick 
was not included.

IMPORTANT: 

Use a suction or siphon pump to drain 

gearbox of oil when there is not an oil drain plug.

24

Hours

8

Hours

8

Hours

50

Hrs

Multi-purpose 
spray lube

Multi-purpose 
grease lube

Multi-purpose 
oil lube

Intervals in hours at which
lubrication is required

Lubrication
Legend

Содержание RCF2060





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды