manualshive.com logo in svg

Land Pride RCF2060, Руководство оператора

Поделиться
Скачать
Land Pride RCF2060 Скачать руководство пользователя страница 19

17

Section 3: Adjustments

10/18/16

RCF2060 and RCF2072 Rotary Cutters   326-459M

Table of Contents

3.

Using tractor’s 3-point hydraulic control, raise or 
lower 3-point lift arms until the front blade tip is at the 
desired cutting height.

4.

The top center link should be loose when deck rear is 
supported by the tailwheel. If not, lengthen center 
link until loose. Final adjustment will be made later.

5.

Measure distance from cutting tip of rear blade to 
ground. This distance should be slightly higher than 
the front blade but not more than 1" higher.

6.

If rear blade is lower than the front blade or is more 
than 1" higher than the front blade, then the tailwheel 
height must be adjusted. If needed, see 

“Tailwheel 

Height Adjustment”

 instructions below.

7.

Repeat steps 1 through 6 until tailwheel and 3-point 
arms are adjusted to the desired cutting height.

8.

Set tractor’s 3-point hydraulic control stop once the 
tailwheel and 3-point arms are adjusted properly.

Tailwheel Height Adjustment

Refer to Figure 3-3:

If front blade tip is set at desired cutting height and back 
blade tip is at same height or lower or is higher than front 
blade tip by more than 1", then the tailwheel (#1) must be 
adjusted up or down as follows:

Tailwheel Height Adjustment

Figure 3-3

1.

Use tractor’s 3-point hydraulic control to lift cutter 
until tailwheel (#1) clears the ground.

2.

Remove hex top locknut (#4) and carriage bolt (#3).

3.

Adjust tailwheel as follows:

•

To lower cutting height, raise tailwheel up.

•

To increase cutting height, lower tailwheel down. 

4.

With tailwheel adjusted to the correct height, replace 
5/8"-11 x 1 1/2" GR5 carriage bolt (#3) and top 
locknut (#4). Tighten top locknut to the correct torque.

5.

Readjust tractor’s lower 3-point lift arms as needed. 
See 

Deck Cutting Height

 instructions on page 16.

30989

Tractor Center 3-Point Adjustment

Refer to Figure 3-4: 

Center 3-Point Link Adjustment

Figure 3-4

1.

Lower cutter deck to the nominal cutting height.

2.

Typically the tractor center 3-point link is adjusted so 
that the upper 3-point clevis pin is straight above the 
lower 3-point hitch pins. This arrangement allows for 
optimum ground contour following performance.

3.

Lock tractor center link in this position once correct 
length is achieved. Adjustment on center 3-point link 
can be made depending on customer’s preference.

37952

NOTE:  

Customer may adjust tractor center 3-point 

link to his or her preference. Lengthening tractor 
center 3-point link allows more movement while 
going over raised surfaces. Shortening the link 
allows more movement while crossing over ditches. 
Also, shortening center link allows the cutter to be 
carried higher while traveling. Never lengthen center 
link to where the cutter is carried too low.

Содержание RCF2060





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды