manualshive.com logo in svg

Land Pride RCF2060, Руководство оператора

Поделиться
Скачать
Land Pride RCF2060 Скачать руководство пользователя страница 21

19

Section 4: Operating Instructions

10/18/16

RCF2060 and RCF2072 Rotary Cutters   326-459M

Table of Contents

•

Keep blade bolt access hole covered at all times except when 
servicing cutter blades. Make sure driveline is disconnected 
from the tractor before servicing cutter blades. 

•

Perform schedule maintenance. Check for loose hardware, 

missing parts, broken parts, structural cracks, and high wear. 
Make repairs before putting the implement back into service. 
Serious breakdowns can result in injury or death.

•

Use this implement for its intended purpose only. Do not use 

implement to lift or carry objects; to pull fence posts, stumps, 
or other objects; or to tow other equipment. Doing so can 
damage the unit, cause serious bodily injury, or death.

!

CAUTION

To avoid serious injury:

•

Buildup of debris around moving parts and gearboxes is a fire 

hazard. Keep rotating parts and gearboxes free from debris to 
avoid serious injury and property damage.

•

Improper oil level can cause bearing failure and be a fire 

hazard. Maintain proper gearbox oil level to avoid serious 
injury and property damage. 

•

Do not exceed rated cutting capacity of your cutter. See 

specifications & capacities for specified cutting capacity. 
Exceeding ratted cutting capacities can damage drive 
components, cutter blades, and deck components.

Inspection of Tractor & Cutter

Make the following inspections with cutter attached to a 
tractor, PTO disengaged, and completely stopped:

1.

Park tractor and cutter on a level surface. 

2.

Disengage PTO, place gear selector in park, set park 
brake, shut tractor off, and remove switch key. Make 
sure cutter blades have come to a complete stop 
before dismounting from tractor. 

3.

Inspect tractor safety equipment to make sure it is 
installed and in good working condition.

4.

Inspect cutter safety equipment to make sure it is 
installed and in good working condition. 

5.

Check driveline to make certain it is securely 
connected to the tractor PTO shaft and cutter 
gearbox shaft. Also, make certain that the guards are 
in good working condition and in place.

6.

Carefully raise and lower implement to ensure that 
the drawbar, tires, and other equipment on the tractor 
do not contact cutter frame or driveline. 

7.

Check all hoses and wires to be sure that they will not 
come in contact with rotating driveline.

8.

With cutter deck resting on solid supports, PTO 
disengaged, and blade rotation completely stopped:

•

Check for and remove foreign objects wrapped 
around blade spindles.

•

Check for nicked, bent, broken, and worn cutting 
blades. Replace or sharpen blades as required. 
Refer to 

“Cutter Blade Maintenance” 

on page 22.

9.

Remove solid supports from under the deck.

10. Verify cutter is set at the correct cutting height. See 

“Deck Leveling & Cutting Height” 

on page 16. 

The remaining inspections are made by engaging the 
PTO to check for vibrations.

!

WARNING

Stop PTO immediately if vibration continues after a few 
revolutions during start-up and anytime thereafter. Wait for 
PTO to come to a complete stop before dismounting from 
tractor to check for probable causes. Make necessary repairs 
and adjustments before continuing.

11. Start tractor, set throttle to idle or slightly above idle, 

and slowly engage PTO. Initial start-up vibration is 
normal and should stop after a few revolutions. Stop 
PTO rotation immediately if vibration continues. 

12. Once cutter is running smoothly, increase tractor 

PTO speed to 540 RPM. Stop PTO rotation 
immediately if vibration occurs.

13. Investigate cause of vibration and make repairs 

before putting cutter back into service.

Transporting

!

WARNING

When traveling on roadways, transport in such a way that 
other vehicles may pass safely. Use accessory lights, clean 
reflectors, and a slow moving vehicle (SMV) sign that are 
visible to warn operators in other vehicles of your presence. 
Always comply with all federal, state, and local laws.

1.

Make sure driveline does not contact tractor or cutter 
when raising cutter to transport position.

2.

Reduce tractor ground speed when turning and leave 
enough clearance so cutter does not contact 
obstacles such as buildings, trees, or fences.

3.

Limit transport speed to 20 mph. Transport only with 
a tractor of sufficient size and horsepower. 

4.

When traveling on roadways, transport in such a way 
that faster moving vehicles may pass you safely.

5.

Shift tractor to a lower gear when traveling over rough 
or hilly terrain.

IMPORTANT: 

Do not exceed implement’s rated PTO 

speed. Excessive speed will cause damage to the 
power train components.

IMPORTANT: 

Always disengage PTO before raising 

3-point arms and implement to transport position.

Содержание RCF2060





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды