manualshive.com logo in svg

Land Pride RCF2060, Руководство оператора

Поделиться
Скачать
Land Pride RCF2060 Скачать руководство пользователя страница 26

24

Section 5: Maintenance & Lubrication

RCF2060 and RCF2072 Rotary Cutters   326-459M

10/18/16

Table of Contents

3.

Start tractor and engage PTO drive for 2-3 seconds 
to permit slippage of the clutch surfaces. Disengage 
PTO, then re-engage a second time for 2-3 seconds. 
Disengage PTO, shut off tractor, and remove key. 
Wait for all components to stop before dismounting 
from tractor.

4.

Inspect clutch and ensure that the scribed markings 
made on the clutch plates have changed position. 
Slippage has not occurred if any two marks on the 
friction disc and plate are still aligned. A clutch that 
has not slipped must be disassembled to separate 
the friction disc plates. See 

“Clutch Assembly and 

Disassembly” 

on page 24.

5.

Tighten each of the 8 spring retainer nuts on the 
clutch housing exactly 2 revolutions to restore the 
clutch to the original setting pressure.

6.

The clutch should be checked during the first hour of 
cutting and periodically each week. An additional set 
of scribe marks can be added to check for slippage. 
See Figure 5-4 on page 24 to adjust spring length.

Clutch Assembly and Disassembly

Disassembly

Refer to Figure 5-3:

See 

IMPORTANT NOTE

 above before disassembling 

clutch. After measuring and recording each spring length, 
remove spring retainer nuts (#1), springs (#2), and bolts 
(#3). Each friction disc (#4) must then be separated from 
the metal surface adjacent to it. Refer to the Parts Manual 
for a detailed parts breakdown.

Inspection

Inspect all parts for excessive wear and condition. Clean 
all parts that do not require replacement.The original 
friction disc thickness is 1/8" (3.2mm) and should be 
replaced if thickness falls below 3/64" (1.1mm). If 
clutches have been slipped to the point of “smoking”, the 
friction discs may be damaged and should be replaced. 
Heat build-up may also affect the yoke joints. 

Assembly

Refer to Figure 5-4:

Reassemble each friction disc (#4) next to the metal plate 
it was separated from. Install bolts (#3) through the end 
plates and intermediate plates as shown. Place springs 
(#2) over bolts (#3) and secure with nuts (#1).

Refer to Figure 5-4:

Progressively tighten each spring retainer bolt until 
correct spring height “A” dimension is obtained.

IMPORTANT: Refer to Figure 5-4.

 

Be Sure to 

measure and record length (“A”) of each clutch 
spring before disassembling clutch.

Clutch Disassembly

Figure 5-3

Clutch Adjustment

Figure 5-4

Accessory Skid Shoe Maintenance

Refer to Figure 5-5 on page 25:

!

WARNING

Excessive wear on skid shoes can damage side panels, cause 
inadequate operation of cutter, and create a safety hazard. 
Always replace skid shoes at the first sign of wearing thin.

There are skid shoes mounted on the cutter sides. Check 
both skid shoes for wear and replace if necessary. Order 
only genuine Land Pride parts from your local Land Pride 
dealer.

1.

Remove 3/8" hex whiz nuts (#3), 3/8" plow bolts (#2), 
and skid shoe (#1) as shown. 

2.

Plow bolts should be checked for wear and replaced 
if necessary.

3.

Attach new skid shoe (#1) to cutter with existing 
3/8" plow bolts (#2) and secure with 3/8" hex whiz 
nuts. Tighten to the correct torque.

4.

Repeat on opposite side.

19783

Model 

No.

Driveline 

No.

PTO 

Speed

Cat 
No.

A (inches) 

Spring Height

RCF2060

312-026A

540

3

1.269" to 1.312"

826-657C

RCF2072

312-728A

540

3

1.269" to 1.312"

826-656C

A = Measured length of each spring 
before disassembling slip clutch.

Use “A” dimension in table below 
if measurements were not taken 
before disassembling slip clutch.

24600

Содержание RCF2060





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды