manualshive.com logo in svg

Land Pride RCF2060, Руководство оператора

Поделиться
Скачать
Land Pride RCF2060 Скачать руководство пользователя страница 27

25

Section 5: Maintenance & Lubrication

10/18/16

RCF2060 and RCF2072 Rotary Cutters   326-459M

Table of Contents

Skid Shoe Replacement

Figure 5-5

Long Term Storage

Clean, inspect, service, and make necessary repairs to 
the cutter when parking it for long periods and when 
parking it at the end of a working season. This will help 
ensure the cutter is ready for field use the next time you 
hook-up to it.

!

DANGER

Always disconnect driveline from tractor PTO shaft before 
servicing drive train and cutter blades. The PTO can be 
engaged if tractor is started causing bodily injury or death.

!

DANGER

Always secure equipment with solid supports before working 
under it. Never work under equipment supported by concrete 
blocks or hydraulics. Concrete blocks can break, hydraulic 
lines can burst, and/or hydraulic controls can be actuated 
even when power to hydraulics is off.

!

CAUTION

Always store cutter with 3-point hitch pivoted back as far as 
possible. The floating 3-point hitch when not hooked to a 
tractor can fall backwards unexpectedly causing bodily injury.

1.

Clean off any dirt and grease that may have 
accumulated on the cutter and moving parts. Scrape 
off compacted dirt from the bottom of deck and then 
wash surface thoroughly with a garden hose. A 
coating of oil may also be applied to the lower deck 
area to minimize oxidation.

30993

Land Pride Skid Shoe Replacement Parts

Item Part No.

Part Description

1

326-221D

SKID SHOE

2

802-603C

PLOW 3/8" - 16 x 1" GR5

3

803-198C

NUT HEX WHIZ 3/8-16 PLT

2.

Check blades and blade bolts for wear and replace if 
necessary. See 

“Cutter Blade Maintenance” 

on 

page 22.

3.

Inspect for loose, damaged or worn parts, and adjust 
or replace as needed.

4.

Repaint parts where paint is worn or scratched to 
prevent rust. Ask your Land Pride dealer for aerosol 
touch-up paint. Paint is also available in touch-up 
bottles with brush, quarts, and gallon sizes by adding 
TU, QT, or GL to the end of the aerosol part number.

5.

Replace all damaged or missing decals.

6.

Lubricate as noted in 

“Lubrication Points”

 starting 

on page 26.

7.

Store cutter on a level surface in a clean, dry place. 
Inside storage will reduce maintenance and make for 
a longer cutter life.

8.

Follow all unhooking instructions on page 20 when 
disconnecting tractor from cutter.

Ordering Replacement Parts

Land Pride offers equipment in factory standard beige 
color with black highlights. Equipment in special colors 
may be purchased in Green, Red, or Orange. Because of 
the variety of colors available, special attention must be 
given to the part number to prevent ordering the wrong 
replacement part. A suffix number corresponding to one 
of the colors below must be added at the end of Land 
Pride’s part number when ordering a replacement part 
with that color. Parts ordered without a suffix number will 
be supplied in factory standard colors.

For example, if you are ordering a replacement part with 
part number 555-555C and the existing part is red, then 
add the suffix 83 to the end of the number to make the 
part number read 555-555C83.

Land Pride Aerosol Touch-up Paint

Part No.

Part Description

821-011C

PAINT LP BEIGE AEROSOL SPRAY CAN

821-002C

PAINT LP BLACK AEROSOL SPRAY CAN

821-054C

PAINT MEDIUM RED AEROSOL SPRAY CAN

821-058C

PAINT GREEN AEROSOL SPRAY CAN

821-066C

PAINT ORANGE AEROSOL SPRAY CAN

81  . . . . . .  Green
82  . . . . . .  Orange

83  . . . . . . . Red
85  . . . . . . . Black

Содержание RCF2060





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды