background image

3

 

6.9  REFRIGERATION DECK REMOVAL.................................................................................20

 

6.10  PRODUCT COMPARTMENT COOLING FAN/COIL REMOVAL.........................................20

 

6.11  WATER CALIBRATION VALVE REMOVAL.........................................................................21

 

6.12  FLOW WASHER REPLACEMENT......................................................................................21

 

6.13  POWER SUPPLY BOX REMOVAL.....................................................................................21

 

6.14  ELECTRONICS BOARD REMOVAL..................................................................................22

 

6.15  WRAPPER REMOVAL........................................................................................................22

7. TROUBLESHOOTING...........................................................................................................22-26

8.  DISPENSER DISPOSAL.............................................................................................................26

9.   ILLUSTRATIONS, PARTS LISTINGS, WIRING, AND WATER FLOW DIAGRAMS..................26

 

9.1   COMPRESSOR DECK ASSEMBLY...............................................................................28-29

 

9.2   WATER CIRCUIT/TANK ASSEMBLY.............................................................................30-31

 

9.3   INSULATED TANK ASSEMBLY.....................................................................................32-33

 

9.4   INTERNAL CABINET ASSEMBLY.................................................................................34-35

 

9.5   PUMP PLATFORM ASSEMBLY.....................................................................................36-37

 

9.6   WRAPPER, DOOR, DRIP TRAY ASSEMBLY................................................................38-39

 

9.7   WIRING DIAGRAM.............................................................................................................40

Содержание MOO











































Отзывы: