Laing Innotech LTC 302 Скачать руководство пользователя страница 3

Страница: 3 / 57

Instruction LTC 11 Laing Innotech GmbH + Co. KG Althuette Germany

- 3 -

Precondition start of operation of the controller

- 19 -

Start of operation

- 19 -

Current based collision detection

- 19 -

GyroSense based collision detection

- 20 -

Reference run

- 20 -

Determine the stroke by the reference run

- 21 -

Safety zone

- 21 -

Safety Input

- 21 -

Automatic motor recognition

- 23 -

Control through control panels

- 23 -

All Control panels

- 23 -

Control panels with memory keys

- 23 -

Control panels with height indication

- 24 -

Configuration of the controller though the “LM” control panels (control panels without height

indication)

- 24 -

Store memory positions with “LM” control panels

- 24 -

User height limit adjustment by “LM” control panels

- 25 -

Adjusting upper and lower limit

- 25 -

Delete user height limits

- 25 -

Change the sensitivity of the collision detection by “LM” control panels

- 26 -

Initiate a reference run by “LM”

- 26 -

Stroke limit adjustment by “LM” control panels

- 26 -

Adjust upper and lower stroke limit

- 26 -

Delete stroke limits

- 27 -

Configuration of the controller though the “LD” control panels (with height indication)

- 28 -

Operation of “LD” control panels with two buttons

- 28 -

Store memory positions by the “LD” control panels

- 28 -

Memory key handling by the “LD” control panels

- 28 -

User height limit adjustment by the “LD” control panels

- 29 -

Adjust upper and lower limit

- 29 -

Delete user height limits

- 29 -

Change the sensitivity of the collision detection by the “LD” control panels

- 30 -

Initiate a reference run by the “LD” control panels

- 30 -

Change height indication from centimeter to inch by the “LD” control panels

- 30 -

Enter service menu by the “LD” control panel

- 31 -

Rest user settings

- 31 -

Stroke limitation adjustment by “LD” control panels

- 32 -

Adjust stroke upper and lower limit

- 32 -

Delete stroke limits

- 33 -

Содержание LTC 302


























































Результаты поиска

Содержание LTC 302

Отзывы:

Похожие инструкции для LTC 302

Бренды по названию

Популярные бренды

Laing Innotech LTC 302, Инструкция по установке и эксплуатации

Результаты поиска

Содержание LTC 302

Отзывы:

Похожие инструкции для LTC 302

Бренды по названию

Популярные бренды