Laing Innotech LTC 302 Скачать руководство пользователя страница 6

Страница: 6 / 57

Laing Innotech GmbH + Co. KG Althuette Germany Instruction LTC 11

- 6 -

For all Laing Table Controllers and all accessories (products) please note:

•

Before any work is done with the products, read the instruction manual

and follow the instructions!

•

The products may only be used as intended. Danger may occur if products

are used in another way or in other applications than the intended ones.

•

The installation may only be performed by qualified personnel with the

required knowledge and the required capabilities!

•

When making electrical connections, applicable electrical codes must be

observed in respect to the way the connection is made, as well as, who is
authorized to perform such connection.

•

Electrical installations can only be made by authorized personnel!

•

Operation outside the specified operation limits is not allowed!

•

Operation outside the specified environmental limits is not allowed!

For the operation of height adjustable tables please note:

•

Operation of a height adjustable table is only allowed after being instructed

by a person familiar with the product or after thorough study of the
instruction manual!

•

Children are not allowed to play with the table!

•

When operated, no persons are allowed on the table top!

•

Danger of collision!

The table must be placed in a way that it can operate

without colliding with any objects like drawers or window sills!

•

Danger of injury by squeezing!

The table must be placed and operated

so that no person can be squeezed between the table top or other parts of
the table and other objects in the vicinity of the table.

•

Kids under the age of 8 and persons with mental or physical disabilities

are only allowed to operate the table if they have been sufficiently
familiarized with the operation of the table and if it is certain, that they will
not be over challenged by the operation of the table!

•

Use of the table is only permitted in closed buildings where it can be

insured the no water or high humidity can get to the electrical parts!

The controllers are manufactured and tested using the utmost care. Should
there be a problem, please contact our service department.

Design of the table controllers

•

Highly efficient switching power supply drives one, two, three or four motor

channels.

•

The motor channels are controlled by a powerful processor.

•

The processor can be configured to a wide variety of applications by an

easy to use configuration software.

•

The aluminum housing provides superior heat dissipation, that’s why in

most applications the cool down time is not determined by the controller
but by the motors connected to the controller.

•

Port for the OptoSense Sensor

Содержание LTC 302


























































Результаты поиска

Содержание LTC 302

Отзывы:

Laing Innotech LTC 302, Инструкция по установке и эксплуатации, Страница: 6 / 57

Результаты поиска

Содержание LTC 302

Отзывы: