Laing Innotech LTC 302 Скачать руководство пользователя страница 50

Страница: 50 / 57

Laing Innotech GmbH + Co. KG Althuette Germany Instruction LTC 11

- 50 -

Failure codes indicated by the control panels

The following failure indication will be shown by the control panels with height
indication. If control panels without height indication are used, refer to the blinking
of the LED on the controller to determine the failure mode.

Indicated Failure code

LED blinking

Failure

Failure solution

con

Communication error

There is no
communication between
the controller and the
control panel. Check the
electrical connection

- - -

Reference mode

The controller entered
reference mode, a
reference run must be
performed

LED blinking:

long short short short

EEPROM initialization
error

Reset error by pressing
any key.

If the Error remains
restart system by
unplugging the power
cable of the controller
and plugging it in again
after 20 seconds.

If the error reoccurs the
controller may be
damaged, contact the
supplier

LED blinking:

short long short short

EEPROM write error

Reset error by pressing
any key.

If the Error remains
restart system by
unplugging the power
cable of the controller
and plugging it in again
after 20 seconds.

Содержание LTC 302


























































Результаты поиска

Содержание LTC 302

Отзывы:

Похожие инструкции для LTC 302

Бренды по названию

Популярные бренды

Laing Innotech LTC 302, Инструкция по установке и эксплуатации

Результаты поиска

Содержание LTC 302

Отзывы:

Похожие инструкции для LTC 302

Бренды по названию

Популярные бренды