Laing Innotech LTC 302 Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 57

background image

Laing Innotech GmbH + Co. KG Althuette Germany Instruction LTC 11

- 32 -

•

Press the “up” arrow key 4 times quickly one after another

•

Reaching the program mode will be confirmed by a sound

•

The display will now show P01

•

Press the “up” or “down” arrow key until the display shows P12

•

Press the “memory one” key shortly to enter the menu.

•

The display now will show P30

•

Pressing the memory one key shortly, will reset the user settings

•

To leave the menu item press the “memory two” key

Stroke limitation adjustment by “LD” control panels

Adjust stroke upper and lower limit

In some cases, the table may be built in a way that the maximum travel of the
drive is limited by some additions to the table like facings. In this case a stroke
upper and lower limit can be adjusted what limits the stroke of the drives. The
user height then can only be adjusted within the adjusted stroke range.

Before the stroke limits are adjusted, the user height limits have to be
deleted when the stroke limits will reach into the user height limit range!

As the controller will be supplied with set limits, changes can only be made
when the present value is deleted as described below, after that a new limit
can be set.

•

Move the table top by use of the arrow keys to the minimum or maximum

desired height

•

Press the “up” arrow key 4 times quickly one after another

•

Reaching the program mode will be confirmed by a sound

•

The display will now show P01

•

Press the “up” or “down” arrow key until the display shows P12

•

Press the “memory one” key shortly to enter the menu.

•

The display now will show P30

•

Press the “up” or “down” arrow key until the display shows:

o

P31 for adjustment of the upper height limit, the table must be at the

maximum position

o

P32 for adjustment of the lower height limit, the table must be at the

minimum position

•

Press the “memory one” key shortly to store the selected limit

•

The successful storage of the user position will be confirmed by the sound

shown

The top and lower positions must keep a minimum distance so that
the table can still move after the new limits have been adjusted. This
minimum distance is defined in the parameter set entered into the

«
...
30
31
32
33
34
...
»

Содержание LTC 302


























































Отзывы:

Нет отзывов

Похожие инструкции для LTC 302

Бренд: ABB Страницы: 63

Бренд: K&K Страницы: 6

Бренд: Tapeswitch Страницы: 13

Бренд: Dahua Страницы: 58

Бренд: Parker Страницы: 21

Бренд: Parker Страницы: 26

Бренд: Parallax Страницы: 3

Бренд: Vageo Страницы: 2

Бренд: tau Страницы: 9

Бренд: tau Страницы: 8

SensoTimer ST6 Duo eco!ogic

Бренд: Kärcher Страницы: 96

SmartStuff Series

Бренд: TCP Страницы: 2

Бренд: Hakko Electronics Страницы: 2

Бренд: DNF Controls Страницы: 22

Бренд: Freescale Semiconductor Страницы: 34

Бренд: Matelec Страницы: 2

Бренд: Magicar Страницы: 9

Бренд: DEUTSCHMANN AUTOMATION Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды