Laing Innotech LTC 302 Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 57

Laing Innotech LTC 302 Скачать руководство пользователя страница 38

Laing Innotech GmbH + Co. KG Althuette Germany Instruction LTC 11

- 38 -

Controller control by OptoSense

•

Hold your hand about 5 cm or 2 inch over the OptoSense sensing element

•

After about one second, an LED will come on within the sensing element

which indicates that the OptoSense is now active

•

If, after activation, the hand is moved up for only a small distance the table

will start to move upwards until the hand is moved outside the sensing
area of the OptoSense Sensor

•

If, after activation, the hand is moved down for only a small distance the

table will start to move downwards until the hand is moved outside the
sensing area of the OptoSense Sensor

•

After movement starts, the hand can be moved up or down or even put on

the sensor, the table will continue in the direction it started until the hand is
moved outside the sensing area of the OptoSense Sensor

•

If, after activation, the hand is not moved for about 2 seconds, the sensor

will deactivate until the hand or any other object is removed.

«
...
36
37
38
39
40
...
»

Содержание LTC 302


























































Отзывы:

Нет отзывов