laguna C FLUX 1 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 54

background image

1.5HP Mobile Dust Cyclone Manual

2

IMPORTANT SAFETY INSTRUCTIONS

READ AND UNDERSTAND ALL WARNINGS AND OPERATING

INSTRUCTIONS BEFORE USING THIS EQUIPMENT. Failure to follow all instructions listed
below, may result in electric shock, fire, and/or serious personal injury or property
damage.

Woodworking can be dangerous if safe and proper operating procedures are not followed.
As with all machinery, there are certain hazards involved with the operation of the product.
Using the machine with respect and caution will considerably lessen the possibility of
personal injury. However, if normal safety precautions are overlooked or ignored, personal
injury to the operator may result. Safety equipment such as guards, push sticks, hold-
downs, featherboards, goggles, dust masks and hearing protection can reduce your
potential for injury. But even the best guard won’t make up for poor judgment,
carelessness or inattention.

Always use common sense

and exercise caution in the

workshop. If a procedure feels dangerous, don’t try it. Figure out an alternative procedure
that feels safer.

REMEMBER:

Your personal safety is your responsibility.

This machine was designed for certain applications only. We

strongly recommend that this machine not be modified and/or used for any application
other than that for which it was designed. If you have any questions relative to a
particular application, DO NOT use the machine until you have first contacted the
manufacturer to determine if it can or should be performed on the product.

If you have any questions relative to its application DO NOT use the product until you
have contacted the manufacturer and we have advised you.

When using an electrical appliance, basic precautions should always be followed, including
the following:

READ ALL INSTRUCTIONS BEFORE USING (THIS APPLIANCE)

To reduce the risk of fire, electric shock, or injury:

1. Do not leave appliance when plugged in. Unplug from outlet when not in use and before
servicing.
2. Do not use outdoors or on wet surfaces
3. Do not allow to be used as a toy. Close attention is necessary when used by or near
children.
4. Use only as described in this manual. Use only manufacturer’s recommended
attachments.
5. Do not use with damaged cord or plug. If appliance is not working as it should, has
been dropped, damaged, left outdoors, or dropped into water, return it to a service center.

«
...
6
7
8
9
10
...
»

Содержание C FLUX 1























































Отзывы:

Нет отзывов

Похожие инструкции для C FLUX 1

Бренд: ZIPPER MASCHINEN Страницы: 31

Бренд: laguna Страницы: 36

Бренд: Elektra Beckum Страницы: 9

Бренд: Chiko Страницы: 13

Бренд: Chiko Страницы: 70

Бренд: CHIKO AIRTEC Страницы: 20

CKU-400AT-HC-V1

Бренд: Chiko Страницы: 19

CKU-080AT2-HC-CE

Бренд: Chiko Страницы: 24

CBA-1000AT2-HC-DSA-V1

Бренд: CHIKO AIRTEC Страницы: 25

Бренд: Chiko Страницы: 23

Laser Clean CKU-050-ACC

Бренд: Chiko Страницы: 28

Бренд: Chiko Страницы: 47

Бренд: CHIKO AIRTEC Страницы: 67

CBA-750AT3-HC-DSA-V1

Бренд: Chiko Страницы: 64

CBA-1500AT3-HC-DSA-V1

Бренд: Chiko Страницы: 70

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды