laguna C FLUX 1 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 54

background image

1.5HP Mobile Dust Cyclone Manual

6

Used without the safety alert symbol indicates potentially hazardous

situation which, if not avoided, may result in property damage.

GENERAL SAFETY RULES

WARNING FAILURE TO FOLLOW THESE RULES MAY RESULT

IN SERIOUS PERSONAL INJURY.

FOR YOUR OWN SAFETY, READ AND UNDERSTAND THE INSTRUCTION MANUAL
BEFORE OPERATING THE MACHINE.

Learn the unit’s application and limitations as well

as the specific hazards peculiar to it.

KEEP WORK AREA CLEAN.

Cluttered areas and benches invite accidents.

DON’T USE IN DANGEROUS ENVIRONMENT.

Don’t use this unit in damp or wet

locations, or expose it to rain. Keep work area well-lighted.

KEEP CHILDREN AND VISITORS AWAY.

All children and visitors should be kept a safe

distance from work area.

DISCONNECT UNIT

before servicing.

CHECK DAMAGED PARTS.

Before further use of the unit, properly repair or replace any

part that is damaged.

FAILURE TO FOLLOW THESE RULES MAY RESULT IN

SERIOUS INJURY.

ADDITIONAL SAFETY FOR DUST COLLECTORS

Intended use.

This dust collector is only intended for collecting wood dust and chips from

woodworking machines. Do not use this dust collector to collect metal, dirt, pebbles,
drywall, asbestos, lead paint, silica, liquids, aerosols, or any flammable, combustible, or
hazardous materials.

Hazardous dust.

Dust created while using machinery may cause cancer, birth defects, or

long-term respiratory damage. Be aware of dust hazards associated with each work piece
material, and always wear a NIOSH-approved respirator to reduce your risk.

«
...
10
11
12
13
14
...
»

Содержание C FLUX 1























































Отзывы:

Нет отзывов

Похожие инструкции для C FLUX 1

Бренд: Power Fist Страницы: 20

Бренд: King Industrial Страницы: 12

Бренд: King Industrial Страницы: 2

Бренд: King Industrial Страницы: 5

Бренд: King Industrial Страницы: 8

Бренд: King Industrial Страницы: 9

Бренд: King Industrial Страницы: 10

Бренд: King Industrial Страницы: 11

Бренд: KNOVA Страницы: 22

Бренд: Enke Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды