laguna C FLUX 1 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 54

background image

1.5HP Mobile Dust Cyclone Manual

3

6. Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord
around sharp edges or corners. Do not run appliance over cord. Keep cord away from
heated surfaces.
7. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
8. Do not handle plug or appliance with wet hands.
9. Do not put any object into openings. Do not use with any opening blocked; keep free of
dust, lint, hair, and anything that may reduce air flow.
10. Keep hair, loose clothing, fingers, and all parts of body away from openings and
moving parts.
11. Turn off all controls before unplugging.
12. Use extra care when cleaning on stairs.
13. Do not use to pick up flammable or combustible liquids, such as gasoline, or use in
areas where they may be present.
14. Connect to a properly grounded outlet only. See Grounding Instructions.

SAVE THESE INSTRUCTIONS

1. Read and understand the warnings posted on the machine and in this manual.

Failure to comply with all of these warnings may cause serious injury.

2. Replace the warning labels if they become obscured or removed.

3. This 1.5HP Portable Cyclone Dust Collector is designed and intended for use by

properly trained and experienced personnel only. If you are not familiar with the
proper and safe operation of this type of dust collector, do not use until proper
training and knowledge have been obtained.

4. Do not use this machine for other than its intended use. If used for other purposes,

LAGUNA TOOLS INC.,

disclaims any real or implied warranty and holds itself

harmless from any injury that may result from that use.

5. Always wear approved safety glasses/face shields while using this machine.

6. Before operating this dust collector, remove tie, rings, watches and other jewelry,

and roll sleeves up past the elbows. Remove all loose clothing and confine long hair.
Non-slip footwear or anti-skid floor strips are recommended. Do

not

wear gloves.

7. Wear ear protectors (plugs or muffs) during extended periods of operation.

8. Some dust created by power sanding, sawing, grinding, drilling and other

construction activities contain chemicals known to cause cancer, birth defects or
other reproductive harm. Some examples of these chemicals are:

•

Lead from lead based paint.

•

Crystalline silica from bricks, cement and other masonry products.

•

Arsenic and chromium from chemically treated lumber.

«
...
7
8
9
10
11
...
»

Содержание C FLUX 1























































Отзывы:

Нет отзывов

Похожие инструкции для C FLUX 1

MAXIPLY DMP-170

Бренд: AQC Страницы: 20

Бренд: Clear Vue Cyclones Страницы: 17

Бренд: Craftsman Страницы: 16

Бренд: Craftsman Страницы: 40

Бренд: Craftsman Страницы: 40

Бренд: Craftsman Страницы: 44

Бренд: Craftsman Страницы: 48

Бренд: Oneida Air Systems Страницы: 12

Бренд: Oneida Air Systems Страницы: 21

Бренд: Festool Страницы: 118

Бренд: laguna Страницы: 48

Бренд: Klimawent Страницы: 8

Бренд: Dust Right Страницы: 8

Бренд: Craftex Страницы: 15

Бренд: Craftex Страницы: 16

Бренд: Craftex Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды