laguna C FLUX 1 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 54

background image

1.5HP Mobile Dust Cyclone Manual

5

22.Maintain a balanced stance at all times so that you do not fall or lean against the

dust collector. Do not overreach or use excessive force to perform any machine
operation.

23.Use the right tool at the correct speed and feed rate. Do not force a tool or

attachment to do a job for which it was not designed. The right tool will do the job
better and safer.

24.Use recommended accessories; improper accessories may be hazardous.

25.Maintain machinery with care. Follow instructions for lubricating and changing

accessories.

26.Turn off the machine before cleaning. Use a brush or compressed air to remove

dust or debris — do not use your hands.

27.Do not stand on the machine. Serious injury could occur if the machine tips over.

28.Never leave the machine running unattended. Turn the power off and do not leave

the machine until it comes to a complete stop.

29.Never operate or run the machine without closing the drum up against the lid.

Failure to do so will result in the machine amperage increasing and may trip your
circuit.

Familiarize yourself with the following safety notices used in this manual:

SAFETY GUIDELINES - DEFINITIONS

This manual contains information that is important for you to know and understand. This
information relates to protecting YOUR SAFETY and PREVENTING EQUIPMENT PROBLEMS.
To help you recognize this information, we use the symbols below. Please read the manual
and pay attention to these sections.

Indicates an imminently hazardous situation which, if not avoided,

will result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided,

could result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided,

may result in minor or moderate injury.

«
...
9
10
11
12
13
...
»

Содержание C FLUX 1























































Отзывы:

Нет отзывов

Похожие инструкции для C FLUX 1

Бренд: Chiko Страницы: 24

Бренд: Oneida Air Systems Страницы: 12

Бренд: Oneida Air Systems Страницы: 21

Бренд: Nederman Страницы: 55

Бренд: laguna Страницы: 32

Бренд: Power Fist Страницы: 36

Бренд: Fervi Страницы: 29

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды