Laguna Tools PFLUX1 страница 8 Скачать руководство пользователя

Страница: 8 / 53

1.5HP Mobile Dust Cyclone Manual

21.Give your work undivided attention. Looking around, carrying on a conversation and

“horse

play” are careless acts that can result in serious injury.

22.Always maintain a balanced stance so that you do not fall or lean against the dust

collector. Do not overreach or use excessive force to perform any machine
operation.

23.Use the right tool at the correct speed and feed rate. Do not force a tool or

attachment to do a job for which it was not designed. The right tool will do the job

better and safer.

24.Use recommended accessories; improper accessories may be hazardous.

25.Maintain machinery with care. Follow instructions for lubricating and changing

accessories.

26.Turn off the machine before cleaning. Use a brush or compressed air to remove

dust or debris

—

do not use your hands.

27.Do not stand on the machine. Serious injury could occur if the machine tips over.

28.Never leave the machine running unattended. Turn the power off and do not leave

the machine until it comes to a complete stop.

29.Never operate or run the machine without closing the drum up against the lid.

Failure to do so will result in the machine amperage increasing and may trip your

circuit.

Familiarize yourself with the following safety notices used in this manual:

SAFETY GUIDELINES - DEFINITIONS

This manual contains information that is important for you to know and understand. This

information relates to protecting YOUR SAFETY and PREVENTING EQUIPMENT PROBLEMS.
To help you recognize this information, we use the symbols, described earlier. Please read

the manual and pay attention to these sections.

GENERAL SAFETY RULES

FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS INJURY.

Содержание PFLUX1






















































Результаты поиска

Содержание PFLUX1

Отзывы:

Похожие инструкции для PFLUX1

Бренды по названию

Популярные бренды

Laguna Tools PFLUX1, Руководство пользователя

Результаты поиска

Содержание PFLUX1

Отзывы:

Похожие инструкции для PFLUX1

Бренды по названию

Популярные бренды