Laguna Tools PFLUX1 Скачать руководство пользователя

Страница: 14 / 53

1.5HP Mobile Dust Cyclone Manual

Power Supply Circuit Requirements

The power source circuit for your machine must be g r o u n d e d and r a t e d f o r the
am perage given

below. Never replace a circuit breaker on an existing circuit with

one of higher amperage without consulting a qualified electrician to ensure
compliance with wiring codes.

If you are unsure about the wiring codes in your

area or plan to connect your machine to a shared circuit, consult a qualified
electrician.

Circuit Size (220V) .................15 Amp min

Circuit Size (110V) .................25 Amp min

IN ALL CASES, MAKE CERTAIN THE RECEPTACLE IN QUESTION IS PROPERLY GROUNDED.

IF YOU ARE NOT SURE, HAVE A QUALIFIED ELECTRICIAN CHECK THE RECEPTACLE.

110 VOLT Single-Phase Operation

The motor supplied with your machine is a dual voltage, 110/220 Volt motor. It is shipped

ready-to-run for 110 Volt operation. However, it can be converted for 220 Volt operation.

An (appx.) 8’ cord is included, a “plug” is NOT included. A plug must be installed by a

qualified technician.

The machine can be converted from 110 Volt to 220 Volt operation by re-wiring for 220

volts and

replacing

these components rated for 220 volt operation

PDCPF-ACM220V

→

Autoclean motor 220V

PDCPF-ACM220V-C

→

Autoclean capacitor 1.5uF/450VAC

PDCPF15110-220-OV

→

Overload protector 15A

- Plug 220 Volt (source from local electrician, not available from Laguna Tools)

A qualified electrician should do the conversion, or the machine can be taken to an
Authorized Dealer Service Center. When completed, the machine must conform to the

National Electric Code and all local codes and ordinances.

See “110V to 220V

Converting” for more details.

NOTICE

This Machine i s p r e w i r e d f o r 1 1 0 V .

y o u plan to operate the machine at

220V,

you

must

replace

several

components and

rewire the motor

Содержание PFLUX1






















































Результаты поиска

Содержание PFLUX1

Отзывы:

Похожие инструкции для PFLUX1

Бренды по названию

Популярные бренды

Laguna Tools PFLUX1, Руководство пользователя

Результаты поиска

Содержание PFLUX1

Отзывы:

Похожие инструкции для PFLUX1

Бренды по названию

Популярные бренды