Laguna Tools PFLUX1 Скачать руководство пользователя | Manualshive

Страница: 36 / 53

background image

1.5HP Mobile Dust Cyclone Manual

35

OPERATION

1. Make sure at least one blast gate is open, if connected to a dust collection system with blast
gates.

Never operate dust collector with all blast gates closed!

2. Confirm the electrical supply is correct and connected to machine.

3. Make sure no one is working on or doing maintenance to dust collector.

4. To start, press the ON button on either the ON/OFF switch or remote control.
5. To stop, press the OFF button on either the ON/OFF switch or remote control.

MAINTENANCE

CLEANING THE FILTER

This PFLUX1 is equipped with auto clean every 10 minutes for 10 seconds one direction and
another 10 seconds the other direction. The cleaning will continue for one cycle (10 seconds

clockwise, 10 seconds counterclockwise when you shut the machine off. While the canister is

cleaning the yellow LED light on the control panel will illuminate showing that it is in the process
of cleaning.

There is a HEPA filter replacement indicator, which is the same yellow LED light as the cleaning

one. This is based on a timer system and when 2000 hours of running is reached, the light
indication would be flash constantly in one long, two short intervals meaning the HEPA filter

would need to be replaced.

Pressing the REMOTE button five times will reset the flashing light.

To ensure proper operation of this Mobile Dust Cyclone, the HEPA canister filter must have

adequate air flow. This means the filter must be regularly maintained by carefully blowing the

filter clean using compressed air and an air gun to release built-up particulates trapped between
the filter pleats.

DISCONNECT MACHINE FROM POWER!

For heavy duty users, it is recommended to use compressed air on a weekly basis to maintain
maximum filtration efficiency and longer life span of the filter.

«
...
34
35
36
37
38
...
»

Содержание PFLUX1






















































Отзывы:

Нет отзывов

Похожие инструкции для PFLUX1

Бренд: ZIPPER MASCHINEN Страницы: 34

Бренд: Valex Страницы: 16

Бренд: ARBE Страницы: 5

Бренд: Parker Страницы: 26

FUMERESA FRM-H15

Бренд: Showa Denki Страницы: 8

Dust Cyclone M5

Бренд: Mullet Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды