La Germania AMS95C81ANE/20, Инструкция по установке, обслуживанию и эксплуатации

Страница: 6 / 44

6
REPLACING PARTS
Before performing any maintenance operation, disconnect the appliance from the gas supply and electricity network.
To replace parts such as knobs and burners, just remove them from the seats without disassembling any part of the cooker.
To replace parts such as nozzle supports, valves and electric components follow the procedure described in the burner
adjustment paragraph. To replace the valve or the gas thermostat, it is also necessary to disassemble the two rear gas train
brackets, loosening the 4 screws (2 per bracket) that attach it to the rest of the cooker and, unscrew the nuts that attach the
front burner valves to the control support, after removing all the knobs. To replace the gas or electric thermostat, also
disassemble the rear cooker guard, loosening the relative screws, to be able to pull out and reposition the thermostat bulb.
To replace the oven bulb, just unscrew the protection cap that projects out inside the oven.(fig.13)
WARNING: Before replacing the bulb, disconnect the appliance from the electric power supply.
USE AND MAINTENANCE MANUAL
GAS BURNER DIMENSION
Burner Dimension (mm)
Auxiliary Ø 50
Semi-rapid Ø 70
Rapid Ø 95
Ultra-rapid Ø 125
Ultra-rapid dual Ø 135
ELECTRIC HOT PLATE DIMENSION
TIPE OF PLATE
DIMENSION
Electric hot plate Ø 145
Electric hot plate Ø 180
CONTROL PANEL DESCRIPTION
On the control panel, small symbols show the function of each knob or key. Here as follows are the several controls
that a cooker can have:
the symbol or or shows the disposition of burners on the worktop, the full dot identifies the burner in object (in
this case the rear burner on the right).
the symbol or or shows the running of any oven (2+0 switch, gas oven, gas oven with gas grill, gas oven with
electric grill and multifunction oven)
the symbol shows the grill (gas grill, electric grill)
the symbol shows the electric thermostat for electric fan oven.
the symbol shows the oven fan working button as to allow the oven to operates with fan assisted gas. The fan operation of
the oven prevents the operation of the grill, which therefore cannot be used with the fan in action.
the symbol shows the minute minder
the symbol shows the operating key for the rotisserie (only gas oven)
the symbol shows the ignition key for the oven light (all except the electric fan oven)
the symbol shows the push-button for burner ignition
the symbol
shows if keys are in position “on” or “off”
USING BURNERS
A diagram is etched on the control panel above each knob which indicates which burner corresponds to that knob. The burners
can be ignited in different ways depending on the type of appliance and its specific characteristics:
- Manual lighting (it is always possible even when the power is cut off): Turn the knob counterclockwise that corresponds
to the burner selected, setting it to the MAXIMUM position at the etched star (large flame Fig.15) and place a lit match up to the
burner.
- Electric ignition: Turn the knob counterclockwise that corresponds to the burner selected, setting it to the MAXIMUM position
(large flame Fig. 15) and keep on pressing the knob in correspondence of the ignition symbol marked with a star (for cookers
equipped with ignition trough knob) or press the ignition button marked with a star and release it as soon as the burner has
ignited.
- Burner ignition equipped with safety device (thermocouple)(fig.14): Press and turn the knob counterclockwise that
corresponds to the burner selected, setting it to the MAXIMUM position at the etched star (large flame Fig. 15), press the knob
and activate one of the above-mentioned ignition devices. Once ignited, keep pressing the knob for about 10 seconds to allow
the flame to heat the thermocouple. If the burner goes out after releasing the knob, repeat the entire operation.
Note: It is recommended not to try to ignite a burner if the relative flame cap is not in the correct position.
-Use of the dual burner (fig.16)
This model controls both the central and external crown of the burner with just one valve.
To ignite the central crown press and turn the knob to the maximum delivery position 1 and hold it down until ignition: in
this position the internal flame are at maximum of the internal crown.
Turn the knob to position 2 to have the internal crown at the minimum.
Turn the knob to position 3 to have the internal crown ant the external crown at the maximum.
Turn the knob to position 4 to have the internal crown ant the external crown at the minimum.