Chapter 3 Using the Operator Panel
3-44
Press the
MENU
key.
Press the
3
or
4
key repeatedly until
Paper
Handling >
appears.
Press the
2
key.
Press the
3
or
4
key repeatedly until
>Duplex Mode
appears.
Press the
ENTER
key. A blinking question mark (
?
) ap-
pears.
Press the
3
or
4
key to display the desired duplex
mode. The display changes as shown below.
None
(default)
Short edge bind
Long edge bind
When the desired duplex mode displayed, press the
ENTER
key.
Press the
MENU
key. The message display returns to
Ready
.
Selecting the Output Device
You can select whether printouts will be received by the print-
er’s face-down output tray or to the optional document finisher’s
output tray.
Press the
MENU
key.
Press the
3
or
4
key repeatedly until
Paper
Handling >
appears.
Press the
2
key.
Press the
3
or
4
key repeatedly until
>Stack
Select
appears.
Press the
ENTER
key. A blinking question mark (
?
) ap-
pears. The selected output device will be displayed.
Press the
3
or
4
key to display the desired destination.
The output tray changes as shown below.
Face-down tray
Finisher F-up
Finisher F-down
When the desired paper source displayed, press the
ENTER
key.
Press the
MENU
key. The message display returns to
Ready
.
Adjusting the Stitch Positions
When installing the option document finisher DF-75, adjust the
stitch positions using the following procedures. In the default
settings, the stitch position is set in the center of the paper. De-
pending on the paper, a certain amount of deviation will occur.
In this case, also use this menu to adjust the stitch position.
The adjustment can be done by moving the stitch position ad-
justment gear in the document finisher.
For example, select the range from -57 to +57 (1 = approxi-
mately 0.14 mm) to move the stitch position approximately 8
mm as shown in the following figure. The default setting is
000
(center of the paper.)
Paper Handling >
>Duplex Mode
None
>Duplex Mode
?None
Paper Handling >
1
2
3
4
5
6
7
8
1
2
3
>Stack Select
Finisher F-down
>Stack Select
?Finisher F-down
4
5
6
7
8
-57
(Approx. 8 mm)
+57
(Approx. 8 mm)
Feed direction
Default stitch position
(center of the paper)
Содержание FS-9100DN
