KYMCO 125 DINK - Скачать руководство пользователя

Страница: 175 / 400

. A.C. GENERATOR/STARTER CLUTCH

10-2

DINK 200i/125

SERVICE INFORMATION

GENERAL INSTRUCTIONS

All servicing operations and inspections in this section can be made with the engine installed.

Drain the coolant before removing the right crankcase cover.

Be careful not to drain the coolant when the engine temperature is high. (Perform this operation
when the engine is cold.)

Drain the coolant into a clean container.

Drain the engine oil into a clean container before removing the right crankcase cover.

When the right crankcase cover is installed, fill with the recommended engine oil and coolant.
Then, bleed air from the water jacket.

Refer to chapter 17 for A.C. generator inspection.

SPECIFICATIONS

Engine oil: SAE 10W/30#

API-SG

Oil capacity at change: 0.9 liter (0.79 lmp qt, 0.95 US qt)
Coolant: distilled water + coolant concentrate
Coolant capacity: 1370±20cc

SPECIAL TOOLS

Flywheel puller

A120E00003

Flywheel holder

A120E00021

SPECIFICATIONS Unit: mm (in)

Item

Standard

Service Limit

Starter driven gear I.D.

20.025

20.045 (0.801

0.8018)

20.15 (0.806)

Starter driven gear O.D.

42.175

42.2 (1.687

1.688)

41 (1.64)

TORQUE VALUES

Flywheel nut : 5.5 kgf-m (55 N-m, 40 lbf-ft)

TROUBLESHOOTING

Refer to page chapter 17 for A.C. generator troubleshooting.

Starter motor rotates but engine does not start

Faulty starter clutch

Starter motor rotates reversely

Weak battery

Содержание 125 DINK -

















































































































































































































































































































































































































Результаты поиска

Содержание 125 DINK -

Отзывы:

Похожие инструкции для 125 DINK -

Бренды по названию

Популярные бренды

KYMCO 125 DINK -, Руководство по обслуживанию

Результаты поиска

Содержание 125 DINK -

Отзывы:

Похожие инструкции для 125 DINK -

Бренды по названию

Популярные бренды