KYMCO 125 DINK - Скачать руководство пользователя страница 316

Страница: 316 / 400

15.HANDLEBAR/FRONT WHEEL/FRONT BRAKE/

FRONT SHOCK ABSORBER/STEERING STEM

15-19

DINK 200i125

BRAKE MASTER CYLINDER

REMOVAL

When removing the brake hose bolt, cover
the end of the hose to prevent contamination.
Secure the hose to prevent fluid from leaking
out.

Remove the upper handlebar cover (refer to
the

“FRAME COVERS

REMOVAL/INSTALLATION”

section in

the chapter 2).

Drain the front brake hydraulic system (refer
to the

“FRONT BRAKE FLUID”

section in

this chapter).

Remove the brake lever pivot bolt (1) and nut
(2), then remove the brake lever.

Disconnect the brake light switch connectors
(3).

Remove the brake hose oil bolt (4), sealing
washer and brake hose eyelet.

Remove the two bolts (5) from the master
cylinder holder and remove the master
cylinder assembly.

Содержание 125 DINK -

















































































































































































































































































































































































































Результаты поиска

Содержание 125 DINK -

Отзывы:

Похожие инструкции для 125 DINK -

Бренды по названию

Популярные бренды

KYMCO 125 DINK -, Руководство по обслуживанию

Результаты поиска

Содержание 125 DINK -

Отзывы:

Похожие инструкции для 125 DINK -

Бренды по названию

Популярные бренды