KYMCO 125 DINK - Скачать руководство пользователя страница 101

Страница: 101 / 400

. LUBRICATION SYSTEM

4-2

DINK 200i/125

SERVICE INFORMATION

GENERAL INSTRUCTIONS

The maintenance of lubrication system can be performed with the engine installed in the frame.

Drain the coolant before starting any operations.

Use care when removing and installing the oil pump not to allow dust and foreign matters to
enter the engine and oil line.

Do not attempt to disassemble the oil pump. The oil pump must be replaced as a set when it
reaches its service limit.

After the oil pump is installed, check each part for oil leaks.

SPECIFICATIONS Unit: mm (in)

Standard

Service Limit

Inner rotor-to-outer rotor clearance

0.15 (0.006)

0.2 (0.008)

Outer rotor-to-pump body clearance 0.15

0.2 (0.006

0.008)

0.25 (0.01)

Rotor end-to-pump body clearance

0.04

0.09 (0.0016

0.0036)

0.12 (0.0048)

ENGINE OIL

At disassembly:

1.1 liter (0.97 lmp qt, 1.17 US qt)

Engine Oil Capacity

At change:

0.9 liter (0.79 lmp qt, 0.95 US qt)

Recommended Oil

SAE10W30# API: SG

TROUBLESHOOTING

Oil level too low

Poor lubrication pressure

Natural oil consumption

Oil level too low

Oil leaks

Clogged oil filter or oil passage

Worn piston rings

Faulty oil pump

Worn valve guide

Worn valve guide seal

Oil contamination

Oil not changed often enough

Faulty cylinder head gasket

Loose cylinder head bolts

Содержание 125 DINK -

















































































































































































































































































































































































































Результаты поиска

Содержание 125 DINK -

Отзывы:

Похожие инструкции для 125 DINK -

Бренды по названию

Популярные бренды

KYMCO 125 DINK -, Руководство по обслуживанию

Результаты поиска

Содержание 125 DINK -

Отзывы:

Похожие инструкции для 125 DINK -

Бренды по названию

Популярные бренды